Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
See figure 7. 4. Flip up the seat latch safety. See figure 12. 5. Squeeze the seat latch and release the seat from the front trapeze bar. See figure 12. 6. Slide the seat forward and remove it from the power base. 7. Loosen the screws that attach the trapeze bars to the seat posts. See figure 13. 8. Remove the retaining clips that secure the seat posts to the power base. See figure 13. 9. Move the trapeze bars up or down to the desired height. V. C O M F O R T A D J U S T M E N T S V. COMFORT ADJUSTMENTS NOTE: Change the seat dump by raising or lowering only one set of towers (front or back). 10. Reinstall the retaining clips from step 8. 11. Remove each screw from the trapeze bars and apply thread lock. 12. Reinstall each screw into the trapeze bars and tighten. 13. Reinstall the seat and flip down the seat latch safety. 14. Reconnect the controller connector(s) to the power base. 15. Reinstall the rear shroud and tighten the fasteners. Seat Position You can move the seat forward or rearward by changing the extrusion mounting position. To change the position: 1. Unplug the controller connector(s) from the power base. 2. Remove the seat from the power base. 3. Remove both extrusions from the bottom of the seat. 4. Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 14. 5. Fasten the extrusions back onto the bottom of the seat. 6. Reinstall the seat. 7. Reconnect the controller. Manual Recline Seatback Adjustment If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base. To adjust the recline angle: 1. Pull up on the seatback release lever. 2. Lean forward or backwards to the desired position. 3. Release the lever. Figure 14. Seat Position Adjustment Jazzy 610 Series V. COMFORT ADJUSTMENTS V. COMFORT ADJUSTMENTS Seatback Angle Adjustment If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°. To adjust the seatback angle: 1. Remove the adjusting screws from each seat hinge. See figure 15. 2. Set the seatback at the desired angle. 3. Reinstall the adjusting screws to each seat hinge and tighten. Armrest Width Adjustment You can change each armrest’s width independently of the other. NOTE: Changing the armrest width may increase the overall width of your power chair. To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 15. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. Armrest Angle Adjustment To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 15. 2. Loosen the jam nut. 3. Turn the adjusting screw to raise the front of the armrest or to lower the front of the armrest. 4. Tighten the jam nut to lock the adjusting screw into place. Armrest Height Adjustment To change the armrest height: 1. Loosen the two setscrews located on the armrest receiver. 2. Raise or lower the armrest to the desired height. 3. Tighten the setscrews to secure the armrest. Figure 15. Seatback/Armrest Adjustment ARMREST KNOB JAM NUT SEATBACK ANGLE ADJUSTING SCREW ARMREST HEIGHT ADJUSTING SETSCREWS ARMREST ANGLE ADJUSTING SCREW Jazzy 610 Series V . COMFOR T ADJUSTMENTS V . COMFOR T ADJUSTMENTS Controller Position You can move the controller in toward or out away from the armrest, or change the position of the controller for either left-hand or right-hand use. WARNING! Do not place the controller cable so that it can be pinched in the seat frame or the power base frame. To extend the controller: 1. Flip up the armrest so it is perpendicular to the floor. 2. Loosen the setscrew on the controller bracket. See figure 16. 3. Slide the controller into or out of the armrest to the desired position. To change the controller position: 1. Turn off the power to the controller. 2. Loosen the rear shroud fasteners. See figure 6. 3. Remove the rear shroud. 4. Unplug the controller connector(s) from the power base. 5. Cut the wire tie(s) securing the controller cable to the armrest. 6. Flip up the armrest and loosen the setscrew. See figure 16. 7. Slide the controller out of the armrest. 8. Loosen the setscrew in the other armrest. 9. Place the controller in the other armrest. 10. Tighten the setscrew to secure the controller. 11. Use a wire tie to secure the controller cable to the armrest. 12. Plug the controller connector(s) into the power base. 13. Reinstall the rear shroud and tighten the fasteners. NOTE: If your power chair is equipped with a Synergy or TRU-Balance Seating System, refer to the controller adjustment information contained in separate manuals. SETSCREW CONTROLLER BRACKET Figure 16. Underside of Armrest www.pridemobilit...