Votes - 3, Average rating: 4 ( )

Manafacture: Pride Mobility File size: 4.07 mb File name: Language of manual:

WARNING! Do not place the controller harness so that it can be pinched in the seat frame or the power base frame. To extend the controller: 1. Flip up the armrest so it is perpendicular to the floor. 2. Loosen the setscrew on the controller bracket. See figure 18. 3. Slide the controller into or out of the armrest to the desired position. 4. Tighten the setscrew to secure the controller. To change the controller position: 1. Turn off the power to the controller. 2. Gently push down and pull backward at the harness access point on the rear shroud until it releases. See figure 12. 3. Remove the rear shroud. 4. Unplug the controller connector(s) from the power base. 5. Cut the wire tie(s) securing the controller harness to the armrest. 6. Flip up the armrest and loosen the setscrew. See figure 18. 7. Slide the controller out of the armrest. 8. Loosen the setscrew in the other armrest. 9. Place the controller in the other armrest. 10. Tighten the setscrew to secure the controller. 11. Use a wire tie to secure the controller harness to the armrest. 12. Plug the controller connector(s) into the power base. 13. Reinstall the rear shroud by aligning the side and back tabs with the holes in the main shroud. Gently push down and forward until all four tabs lock into place. NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Positioning System, refer to the controller adjustment information contained in separate manuals. Figure 18. Underside of Armrest Figure 19. Foot Platform Adjustment FOOT PLATFORM BRACKET FOOT PLATFORM RETAINING PIN V. COMFORT ADJUSTMENTS V. COMFORT ADJUSTMENTS Foot Platform Height Adjustment The foot platform height is easily adjusted to several different heights. To raise or lower the foot platform: 1. Remove the hardware from the foot platform bracket. See figure 19. 2. Raise or lower the foot platform to the desired height. 3. Reinstall the hardware into the foot platform bracket and tighten. Foot Platform Depth Adjustment You can adjust the depth of the foot platform. To adjust the foot platform depth: 1. Remove the hardware from the foot platform bracket. See figure 19. 2. Move the foot platform in or out to the desired depth. 3. Reinstall the hardware into the foot platform bracket and tighten. Foot Platform Angle Adjustment You can adjust the angle of the foot platform. To adjust the foot platform angle: 1. Flip up the foot platform and locate the screw. See figure 19. 2. Turn the screw to raise or lower the front of the foot platform. Positioning Belt Your power chair may be equipped with a positioning belt that can be adjusted for operator comfort. See figure 20. The positioning belt is designed to support the operator so that he/she does not slide down or forward in theseat. The positioning belt is not designed for use as a restraining device. To install the positioning belt: 1. Remove the rearmost screw that holds the seat hinge to the seat base on both the left and right seat hinges. 2. Insert the screw through the supplied washer, through the positioning belt and into the seat base for each side of the power chair seat. 3. Tighten both screws. To adjust the positioning belt for operator comfort: 1. Once seated, insert the metal tab on one side of the belt into the plastic housing on the opposite side until you hear a click. See figure 20. 2. Pull the excess strap attached to the metal tab until it is secure, but not so tight as to cause discomfort. To release the positioning belt: 1. Press the push button mechanism on the plastic housing. MANDATORY! Make sure the positioning belt is properly secured to the power chair and isadjusted for operator comfort before each use. MANDATORY! Inspect the positioning belt for loose or damaged parts before each use of thepower chair. If you discover a problem, contact your Quantum Rehab Provider for maintenanceand repair. Figure 20. Positioning Belt Adjustment Jazzy 600 Series VI. BATTERIES AND CHARGING VI. BATTERIES AND CHARGING BATTERIES AND CHARGING Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable. Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs. MANDATORY! Battery posts, terminals, and related accessories contain lead andlead compounds. Wear goggles and gloves when handling batteries and wash hands after handling. PROHIBITED! Always use two batteries of the exact same type, chemistry, and amp- hour (Ah) capacity. Refer to the specifications table in this manual and in the manualsupplied with the battery charger for recommended type and capacities. WARNING! Contact your authorized Pride Provider if yo...

Download now

Please, enter two numbers from picture: