Votes - 3, Average rating: 4 ( )

Manafacture: Genie File size: 886.45 kb File name: Language of manual:

5 Observe the diagnostic LED readout. Result: LED should read 23 or --. Test Emergency Stop 6 Push in the ground red Emergency Stop button to the off position. Result: No functions should operate. 7 Pull out the red Emergency Stop button to the on position. Test the Up/Down Functions The audible warnings on this machine and the standard horn all come from the same central alarm. The horn is a constant tone. The descent alarm sounds at 60 beeps per minute. The alarm that goes off when the pothole guards have not deployed sounds at 300 beeps per minute. The alarm that goes off when the machine is not level sounds at 600 beeps per minute. An optional automotive-style horn is also available. 8 Activate the up function. Result: The platform should raise. 9 Activate the down function. Result: The platform should lower. The descent alarm should sound while the platform is lowering. FUNCTION TESTS Test Auxiliary Lowering/Manual Lowering 10 Activate the up function and raise the platform approximately 60 cm. 11 Activate the auxiliary lowering/manual lowering function. Move the toggle switch OR pull the knob OR push the button. Result: The platform should lower. The descent alarm will not sound. 12 Turn the key switch to platform control. At the Platform Controls Test Emergency Stop 13 Push in the platform red Emergency Stop button to the off position. Result: No functions should operate. Test the Horn 14 Pull the red Emergency Stop button out to the on position. 15 Push the horn button. Result: The horn should sound. Part No. 82784 Genie GS-2032 and Genie GS-2632 Operator's Manual Second Edition • Second Printing FUNCTION TESTS Test the Function Enable Switch 16 Do not hold the function enable switch on the control handle. 17 Slowly move the control handle in the direction indicated by the blue arrow, then in the direction indicated by the yellow arrow. Result: No functions should operate. Test the Up/Down Functions 18 Press the lift function select button. 19 Press and hold the function enable switch on the control handle. 20 Slowly move the control handle in the direction indicated by the blue arrow. Result: The platform should raise. The pothole guards should deploy. 21 Release the control handle. Result: The platform should stop raising. 22 Press and hold the function enable switch. Slowly move the control handle in the direction indicated by the yellow arrow. Result: The platform should lower. The descent alarm should sound while the platform is lowering. When lowering the platform, the platform should stop when it is 2.1 m from the ground. Be sure the area below the platform is clear of personnel and obstructions before continuing. To continue lowering, release the control handle, wait 5 seconds, then move the control handle again. Test the Steering Note: When performing the steer and drive function tests, stand in the platform facing the steer end of the machine. 23 Press the drive function select switch. 24 Press and hold the function enable switch on the control handle. 25 Depress the thumb rocker switch on top of the control handle in the direction identified by the blue triangle on the control panel. Result: The steer wheels should turn in the direction that the blue triangle points on the control panel. 26 Depress the thumb rocker switch in the direction identified by the yellow triangle on the control panel. Result: The steer wheels should turn in the direction that the yellow triangle points on the control panel. Genie GS-2032 and Genie GS-2632 Part No. 82784 Second Edition • Second Printing Operator's Manual Test Drive and Braking 27 Press and hold the function enable switch on the control handle. 28 Slowly move the control handle in the direction indicated by the blue arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the blue arrow points on the control panel, then come to an abrupt stop. 29 Slowly move the control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the yellow arrow points on the control panel, then come to an abrupt stop. Note: The brakes must be able to hold the machine on any slope it is able to climb. Test Limited Drive Speed 30 Press the lift function select button. 31 Press and hold the function enable switch on the control handle. Raise the platform approximately 1.2 m from the ground. Result: The pothole guards should deploy. FUNCTION TESTS 32 Press the drive function select switch. 33 Press and hold the function enable switch on the control handle. Slowly move the control handle to the full drive position. Result: The maximum achievable drive speed with the platform raised should not exceed 23 cm per second. If the drive speed with the platform raised exceeds 23 cm per second, immediately tag and remove the ma...

Download now

Please, enter two numbers from picture: