Votes - , Average rating:
(
)
)
Manafacture: Harbor Freight Tools
File size: 1.24 mb
File name: 92987.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Do not modify the Walker and do not use the Walker for a purpose for which it was not intended. 5. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 6. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. 7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product. 8. Use eye protection. Always wear ANSI approved impact safety goggles when assembling this product. 9. Do not exceed the product’s maximum load capacity of 250 Lbs. SKU 92987 For technical questions please call 1-800-444-3353. Page 2 11. Do not allow children to play with, stand upon or climb on the Walker. 12. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. SPECIAL WARNINGS FOR THIS PRODUCT 1. Before use, make certain your Walker is fully opened, the seat is down completely, and the folding bar beneath the seat is in the locked position. 2. Check that both handles are at equal heights. If one is lower than the other, adjust accordingly. Apply gentle pressure to the Handles to test the stability of the Walker before use. 3. Test brakes thoroughly before use. The brake bar on the wheels will prevent the wheels from rolling when the brake is set in the locked position. If the wheels turn while the brakes are locked, have the brakes adjusted by an authorized technician. Under no circumstances should you use this product if the brakes do not lock properly. 4. Always put brakes in the locked position before sitting on the seat. Do not sit on the seat unless you are on even, level ground. 5. Check tires periodically and replace when worn. 6. This product is not a cart or a wheel chair. Do not use it to push or carry people or objects (except for objects in the basket). Do not load more than 25 Lbs. in the basket. 7. Do not exceed the maximum load capacity of 250 Lbs. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Walker, check to make sure that all of the parts listed on page 5 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Assembly Your Walker will require minor assembly before use. It is important that you read the entire manual to become familiar with the product BEFORE you use the Walker. Before using the Walker, check to make sure that the product is intact, undamaged and working properly. Handles If not already in place, set one Collar (21) securely onto each side of the Front Frame (20). Insert the Handle (10) down into the Front Frame (20). Loosen the Knob (22) and insert the Handle (10) down through the Collar (21) on each side of the Handle (10)-see Figure 1. Repeat these assembly steps for the other Handle (10). Attaching the Back rest Bar (6) 1. Insert both ends of the Backrest Bar (6) with Foam Tubing (7) down into the fitting located at the front of the Front Frame (20)-see Figure 2. To do so you must pull out the Pin located on the front of the fitting. While pulling up on the Pin, insert the Bolt (8) located on the Backrest Bar (6) down into the fitting. Release the Pin-see Figure 2. SKU 92987 For technical questions please call 1-800-444-3353. Page 3 2. Pull up on the Backrest Bar (6) to make certain that it is securely locked into place. Attaching the Basket (9) Hang the Basket (9) from the bar located direclty beneath the Plastic Seat (1) and rest the fitted bottom of the Basket (9) onto the bar at the bottom of the Walker. Once the Walker is completely assembled, test it to make certain that it folds and unfolds properly, that the wheels roll, and that the brakes work. Make certain that it is stable and that all hardware is securely tightened. Operation 1. To slow down or stop temporarily, squeeze the Handgrip (3) and the Brake Loop (2) together firmly. Figure 1 Pin Bolt (8) Figure 2 Handle (10) Knob (22) Collar (21) Front Frame (20) 2. To lock the 6” Wheels (18) in place, with your foot push down on the Brake Lock (12) over each rear 6” Wheel (18). Make certain that the Brake Lock (12) is securely in place and that the 6” Wheels (18) are securely locked. 3. To unlock the 6” Wheels (18), release the tab on each Brake Lock (12) with your foot. 4. The Rollator Walker is easily collapsible when...