Manafacture: KitchenAid
File size: 982.06 kb
File name:
|
manual abstract
13 INSTALLATION INSTRUCTIONS Built-in Outdoor Side Burner Installation ¦ Unpack side burner. Remove all packaging materials and remove side burner from carton. ¦ Place side burner into outdoor enclosure, but leave enough room in back to connect to gas supply and electrical single prong plug-in. Install Tank Tray for 20 lb LP Gas Fuel Tank For Models Equipped for Use with a 20 lb LP Tank 1. Position the tank tray for 20lb LP gas fuel tank in the island cabinet. 2. Square the tank tray mounting brackets and mark the mounting hole locations in the island base. 3. Remove the top nuts (4) from the tank tray assembly and lift the tank tray off of the mounting brackets. 4. Install the tank tray mounting brackets to the base or floor of the island using the proper size and type of mounting hardware (not supplied). Tighten mounting hardware. 5. Pre-adjust each of the bottom nuts on the mounting brackets to 3" (7.6 cm) from the base of the island to the top of the nuts. 6. Remount the tank tray back onto the mounting brackets. Replace the 4 top nuts but do not tighten. Dimension A Dimension B Front to back burner 8...." (20.6 cm) 16...." (41.1 cm) Side by side burner 12...." (31.9 cm) 25..." (63.8 cm) WARNING Excessive Weight Hazard Use two or more people to move and install side burner. Failure to do so can result in back or other injury. B 2..." (5.7 cm) 18..." (46.7 cm) 20..." (52.4 cm) A centerline of tank tray A. Top nut B. Tank tray C. Bottom nut D. Bolt E. Mounting bracket A. Screw (Use proper screw for island floor material.) B. Lock washer C. Flat washer A. 20 lb LP gas fuel tank B. Tank tray for 20 lb gas fuel tank C. Top nut (do not tighten) D. Mounting bracket A BC D E A B C 3" (7.6 cm) A D C B 7. The tank tray for the 20 lb LP gas fuel tank must be adjusted so that the bottom of the tank tray is ..." (0.32 cm) above the cabinet door opening and is level. The top nut on each of the mounting brackets is to be loose. Turn the bottom nuts counterclockwise to raise the tank tray and turn the bottom nuts clockwise to lower the tank tray. When the tank tray is level and slides in and out without touching the cabinet door opening at the bottom or top with the 20 lb LP tank installed, tighten the top nuts against the adjustment flange. A B A. Top nut loosened B. Top nut tightened NOTE: A bracket or shelf (not supplied) that is large enough to keep a second 20 lb LP gas fuel tank from being stored in the storage area under the side burner is required to be mounted inside the island. Make Gas Connection Gas Connection to a 20 lb LP Gas Fuel Tank WARNING Explosion Hazard Use a new CSA International approved “outdoor” gas supply line. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 11” (28 cm) water column. Examples of a qualified person include: licensed heating personnel, authorized gas company personnel, and authorized service personnel. Failure to do so can result in death, explosion, or fire. If converting to local LP or Natural gas, follow the instructions in the “Gas Conversions” section. IMPORTANT: A 20 lb LP gas fuel tank must be purchased separately. IMPORTANT: The gas pressure regulator/hose assembly supplied with the side burner must be used. Replacement gas pressure regulator/hose assembly specific to your model, is available from your outdoor side burner dealer. To Install the 20 lb LP Gas Fuel Tank: 1. Open cabinet doors. 2. Pull out the tank tray. Tank tray 3. Place the 20 lb LP gas fuel tank bottom collar into the mounting hole in the tank tray. 4. Tighten the locking screw against the bottom collar of the 20 lb LP gas fuel tank to secure. A BC A. Locking screw B. Mounting hole C. Bottom collar 5. Screw the gas pressure regulator/hose assembly to the 20 lb LP gas fuel tank as shown. (To disconnect, turn off the gas supply to the 20 lb LP gas fuel tank, then unscrew the gas pressure regulator/hose assembly from the 20 lb LP gas fuel tank as shown.) A. 20 lb LP gas fuel tank B. Gas pressure regulator/hose assembly A B connect disconnect 6. Turn on the gas supply. Wait a few minutes for gas to move through the gas line. 7. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found. 8. Slide tank tray back into the cabinet. 9. Go to “Plug in Side Burner” in this section. Gas Connection to Natural Gas or Local LP Gas WARNING Explosion Hazard Use a new CSA International approved “outdoor” gas supply line. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 11” (28 cm) water column. Examples of a qualified person include: licensed heating personnel, authorized gas company personnel, and authorized service personnel. Failure to do so can result in death, explosion, or fire. This installation must conform with local codes and ordinances. In the absence of local codes, installations must conform ...
Other models in this manual:Outdoor Gas Burners - KBZU242VSS (982.06 kb)
Outdoor Gas Burners - W10176789A (982.06 kb)