Failure to do so can cause possible injury, poor performance and may void your warranty. REPLACING AND CLEANING THE AIR FILTER See Figure 8. For proper performance and long life, keep air filter clean. 1. Push down on the latch of the air filter cover; carefully pull the top of the air filter cover so it pivots away from the base. 2. Remove the air filter and clean it in warm soapy water. Rinse and let dry completely. For best performance, replace the air filter annually. 3. Reinstall the air fi

¦ ¦¦¦¦¦Never use for spreading chemicals, fertilizers, toxic substances, or any other hazardous chemical. ¦ ¦¦¦¦¦Use only as directed in this operator's manual. Page 3 SYMBOLS SYMBOLS SYMBOL NAME EXPLANATION . Safety Alert Symbol Precautions that involve your safety. Read the Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Wear Eye and Hearing Protection Wear eye protection which is marked to comply with ANSI Z87.1 as wel

Keep away from corrosive agents such as garden chemicals and de-icing salts. 3 Abide by all Federal and local regulations for the safe storage and handling of gasoline. Excess fuel should be used up in other 2-cycle engine powered equipment. Page 15 TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVETHE PROBLEM CONTACT YOUR AUTHORIZED SERVICING DEALER. PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start: 1.No spark. 2.No fuel. 3.Flooded engine. 4.Starter rope pulls harder now than when new. 1.Chec

ASSEMBLING THE BLOWER TUBES See Figure 2. 1. Screw the nozzle onto the upper blower tube and tighten securely. Check tightness after initial run and retighten if needed. 2. Place clamp around the neck of the blower housing outlet. Do not tighten the wing nut yet. 3. Align the locking tab on upper blower tube with the slot in the blower housing outlet; push the tube into the housing. Twist to lock into place. 4. Rotate the tube so the nozzle is pointing upward as shown. Tighten the wing nut secur

¦ Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches and gardens. ¦ Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away. ¦ Use the full blower nozzle extension so the air stream can work close to the ground. ¦ After using blowers or other equipment, CLEAN UP! Dispose of debris in trash receptacles. ¦ Use the wide sweeper nozzle for the everyday b

This new blower is equipped with the following features. See Figures 1a and 1b. MOTOR The blower has a powerful 30cc engine with sufficient power to handle tough blowing and vacuuming jobs. THROTTLE TRIGGER The blower can be operated at any speed between idle and full throttle. CRUISE CONTROL / THROTTLE LOCK The Cruise control (throttle lock) feature allows the user to operate the blower without holding the throttle trigger.To stop the engine, simply push the Cruise control knob after the engine

See chart later in this section. To mix the fuel: 1. Use a clean container that is approved for use with gasoline. 2. Mix the Premium Exact Mix™ 2-cycle engine oil with unleaded gasoline in the container, according to the instructions on the oil package. IMPORTANT: This engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 ([R + M] / 2) or higher. Do not use automotive oil or 2-cycle outboard oil. NOTE: Premium Exact Mix™ fuel mixture will st

spray can) . 22772 46 PIN-cotter, 3/32 x 3/4 LM-09184-47 1 Qty. 3 ALWAYS FURNISH MODEL AND SERIAL NUMBER WHEN ORDERING PARTS. 9 Low Profile Trailer frame & Cover No. Description Part No. Qt: 1 COVER LM-01231-36 1 2 SIDE ME MBER -f ra me LM-01231-30 2 3 STUD ASSEMBLY-special LM-01231-32 4 4 END BRACKET-frame LM-01231-31 2 5 WASHER-lock, 5/16 LM-09173-56 4 6 NUT-hex, 5/16-18 LM-09173-72 4 7 STOP LM-01231-34 2 8 WASHER-flat, 5/16 LM-09176-42 8 9 NUT-hex lock, 5/16-18 LM-09180-05

Insert the other end of the spring through the hole in the end of the hook. Then place the hook over the lip on the front of the dump cart body (Figure 9). Mounting the Roving Nozzle The roving nozzle attaches to the blower inlet in place of the hose from the mower. For storage a rack is provided for installation on the front of the dump cart (Figure 12.) 1. Install the hose flange and a hose clamp on the plain end of the hose. Secure with one 1/4-20 x 3" machine screw, lockwasher and hex nut

The instructions and parts list for the dump cart will be found packaged with the car . Assembly Mounting the Vacuum Collector 1. Install the drive pulley on the tractor PTO shaft using a 3/16 x 3/16 x 1" key. Secure the pulley with the set screw provided. Install the three belt stops on the tractor frame. The 7/16-14x1-1/4” capscrew provided for the upper belt stop, replaces the original cap screw on the tractor (Figure 1). 2. Install the lift shaft on the rear of the tractor using the two