It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the mower. The blade can be tested for balance by balancing It on a round shaft screwdriver. Remove metal from the heavy side until it balances evenly. NOTE It is recommended that the blade always be removed from the adapter for the best test of balance. C. Reassembly Befo

Place upper handle in position over lower handle, selecting hole for either high or low position. See figure 9. Secure with two curved head bolts (A), lock washers (B) and hex nuts (C) as shown in figure 3. Tighten securely using a 1/2" wrench. FIGURE 3. 4 5. Place the throttle control in position on right side of upper handle. Secure with hex bolt (E) and lock nut (F). See figure 4. NOTE Reference to right and left hand sides of the unit is observed from the operating position. FIGURE 4.

It will not apply where the unit has been used commercially. Warranty service is available through your local authorized service dealer or distributor. UNDER NO CIRCUMSTANCES WILL THE RETURN OF A COMPLETE UNIT BE ACCEPTED BY THE FACTORY UNLESS PRIOR WRITTEN PERMISSION HAS BEEN EXTENDED. Model No. 110-060 110-070 MOWER WOT MLIS Your rotary mower is a precision piece of power equipment, not a plaything. Therefore exercise extreme caution at all times. 1. Remove all sticks, stones, wire and o

v Check that the ventilation slots are not obstructed in any way. Do not use your Turbotrimmer if the safety devices (push button, safety cover) and/ or the filament cassette are damaged or worn. v Never bypass the safety devices. v Inspect the area to be cut before you begin work. Remove any foreign objects (such as stones). Look out for foreign objects (such as stones) while you are working. v If you should come across an obstacle while cutting, turn off the Turbotrimmer. Remove the object and

If you cannot locate an authorized service dealer, contact the manufacturer as set forth on your copy of the Owner’s Registration Card. 1. The blade brake/clutch hand control is a safety device. Never attempt to bypass its operation. Doing so makes the safety device inoperative and may result in personal injury through contact with the rotating blade. This hand control must operate freely in both directions. 2. Striking a solid object can cause damage to the blade brake/clutch or to the engine

Attach the grass catcher frame to grass catcher hitch bracket on rear of the mower by hooking grass catcher into hooks on grass catcher hitch bracket. See figure 9. 2. Lift the rear of grass catcher up. The roller on the grass catcher will push the chute door on the mower open. See figure 9. H^NOTE Figure 9 is shown with the chute door open for photo clarity only. 6 The grass catcher frame will snap into place, -secured by the lock lever. See figure 10. To remove the grass catcher, unhook

All orders should specify the model number of your unit, part numbers, description of parts and the quantity of each part required. BRIGGS AND STRATTON, TECUMSEH AND PEERLESS PARTS AND SERVICE Briggs & Stratton, Tecumseh and Peerless parts and service should be handled by your nearest authorized engine service firm. Check the yellow pages of your telephone directory under the listing Engines—Gasoline, Briggs & Stratton or Tecumseh Lauson. NOTE: If any parts are found to be missing or defectiv

After assembly, service engine .with gasoline and oil as instructed in the separate engine manual packed with your unit. ,NOTE: Reference to right or left hand side of the mower is observed from the operating position. Refer to parts identification on page 4 for location of parts when assembling the mower. Tools Required for Assembly (1) Pair of Pliers (1) 1/2" Wrench or Adjustable Wrench (1) Phillips Screwdriver UNPACKING 1. Remove the lawn mower from the carton by opening the top flaps a

110-120-306, 110-121-306, 110-140-306, and 110-141-306 ROTARY MOWER For one year from date of purchase, MTD Products, Inc., will replace for the original purchaser, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. All transportation charges on parts submitted for replacement under this warranty must be paid by the purchaser. This warranty does not include replacement of parts which become inoperative \ through mis

Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. Always be sure of your footing. A slip and fall can cause serious personal injury. 10. Never operate mower without proper guards, plates or other safety protective devices in place. 11. Muffler and engine become hot and can cause a burn. Do not touch. 12. Do not operate this mower with the chute door open, unless the complete grass catcher or chute