ALL RIGHTS RESERVED MANUAL No. 7-3571 (Rev. 1, 7/28/00) IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects thatcan cause injury and damage! Failure to comply with the following SAFETY instructions could result in seriousinjury or death to the operator or other persons. The owner of the machine must understand these instructionsand must allow only persons who understand these instructions to operate machine. Each pers

Depress belt idler and remove the inside (forward) clutch drive belt. See Figure 1.1. REMOVE INSIDE CLUTCH DRIVE BELT WIRING ELECTRIC CLUTCH HARNESS CONNECTOR CONNECTOR FIGURE 1.1 IMPORTANT: The grass catcher kit includes two different length blower drive belts. Carefully check thepart numbers to insure you install the correct belt onyour machine. 1) Belt Part No. 7-2738 fits ZMT and machines with the # 6-3165 Drive Shaft Lowering Kit installed. 2) Belt Part No. 4-6249 fits all other Mid-Mount m

1, 1/24/03) MANUAL No. 06613 CONTENTS LAWN TRACTOR MODEL IDENTIFICATION Positive identification of the machine will be necessary. Identify the machine with the model number to insure the correct kit is used for that model. The series number or letter of the model number is used in this manual to match the correct kit with the correct model. Refer to Owner’s Manual for correct Series number. The series number for all disc, gear and hydro drive two piece frame models is 0, 1, 2. The series number

The Grass Catcher is optional equipment on some models. 11 18 22 :\ 25 27 _25 24 24 BLOP_ERUNIT GROUP 25 25 CZT / HZT Models 28 26 * Grease Fitting Orientation 12 SntlllllKl-l/tlc lloilr llnl! SrOUll-CJT/ETmedel$ Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 3O Part No. 3046782 91121 90183 3021097 44995 91804 14409 10776 3046824 91527 3047253 91601 91218 3046781 3046853 91541 3022832 90839 3031920 3046854 3031919 90613 3046813 3043613 90122 91560 91518 91305

Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper

Assemble, test, and use only in accordance with the Owner’s Manual instructions. READ and FOLLOW chemical label instructions. Pesticides are hazardous chemicals. KNOW emergency procedures BEFORE handling chemicals. Sprayer leaks, bodily chemical contact, poisoning, and spills require immediate response. AVOID inhaling, ingesting, or coming into contact with any chemicals. WEAR personal protective gear when filling, using, cleaning, and servicing the sprayer. KEEP sprayer and spray materials away

No. Description 18HP Product 2690622 Baron XL, 18HP and 40" Mower Deck (CE/Export) Mfg. No. Description 20HP Product 2690621 Baron XL, 20HP and 40" Mower Deck (CE/Export) 2690625 2420 XL, 20HP and 40" Mower Deck (CE/Export) Mfg. No. Description 21HP Product 2690762 Baron, 21HP and 40" Mower Deck (CE/Export) 2690772 2421, 21HP and 40" Mower Deck (CE/Export) Mfg. No. Description Mower Decks 1695200 40" Mower Deck (CE/Export) 1695201 40" Mower Deck (CE/Export) Part No.: 1734840 Table Of Contents s

HARDWARE REFERENCE Tools Required for Assembly: * 7/16" wrench * 1/2" wrench * Flat Head Screwdriver * Hammer * Pair pliers L-1782-BH-01 3. Parts Reference Parts List L-1782-BH-01 4. REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 22 23 25 26 27 28 29 30 31 32 33 PART NO. B-983 B-1673P C-123 R-618 R-635-01 R-636 R-637-01 R-640 R-653 R-704 R-705-10 R-713-10 R-746 R-755-10 R-1503 R-1835-10 R-2466-10 R-2474-10 R-2473-10 R-775-10 R-803 10M0840P 11M1016P 30M1000P 40M1000P 45M1111P 45M1717P R

IMPORTANT: Please fill out the SNAPPER Product Registration Card immediately and mail to: Snapper's Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253 11 unit breakdown & parts list 12 unit breakdown & parts list S SSn nna aap ppp ppe eer rrZ ZZ- --V VVa aac ccB BBl llo oow wwe eer rrU UUn nni iit ttG GGr rro oou uup pp4 448 88” ””, ,,5 552 22” ””, ,,6 661 11” ””M MMo ood dde eel lls ss Item Part No. Qty Description 1 3046782 1 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13

Figure 11. Tension Springs A. Eyebolt D. Pivot Frame B. Nut, 5/16 E. Nut, 5/16 C. Spring B D C A E Figure 12. Spring Assist Bracket A. Spring Assist Bracket B. Capscrew, 1/2-13 x 1-1/4 C. Lockwasher, 1/2 D. Hex Nut, 1/2-13 E. Hitch 11 Initial Setup & Assembly 2. Increase front tire pressure to 20 psi (138 kPa) to compensate for added weight of the hitch, plus bar and blade. Be sure both tires have equal pressure. 3. From the front of tractor, slide the hitch under the tractor so that the hitch b