Votes - 4, Average rating: 4.8
(
)
)
|
manual abstract
• Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not drive in reverse unless absolutely necessary. Always look down and behind before and while backing. • Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when backing, look behind and down for small children. • Mow up and down slopes (10° Max), not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. • Use a slow speed while on slope or hill. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Husqvarna - 7 8 - Husqvarna ASSEMBLY BAGGER ASSEMBLY 1. Attach hitch tube to support bracket with 3/8-16 x 2 shoulder bolts and secure with flange nuts. HITCH TUBE SUPPORT BRACKET 2. Place the support bracket against the frame rear guard. Using the outer right hole and inner left hole, secure with 5/16 x 1 bolts and 5/16 nyloc nuts. 3. Attach support tube to frame hitch with . x 2. bolt and . nyloc nut. SUPPORT BRACKET HOLES ATTACH HITCH TUBE TO FRAME 4. Place the hood / hitch assembly onto the hitch tube. 5. Open the hood and secure the (2) springs to the bolts on the hood assembly and the hitch assembly. ATTACH SPRINGS TO HITCH AND HOOD SET HOOD/LATCH ASSEMBLY ONTO HITCH TUBE Husqvarna - 9 ASSEMBLY 6. Attach right and left straps to the hood/latch assembly with 3/8-16 x 1 bolts and flange nuts. ATTACH STRAPS TO HINGE ASSEMBLY 9. Secure inner end of straps to unit fuel tank mounts with 3/8-16 x 1 thread forming bolts and flange nuts, as shown. FUEL TANK MOUNT DRAW LATCH MOUNT TABS BAG DRAW LATCH KEEPER 10. With the hood open, secure the (3) bags in place. The back of the bags will hook over the mounting tabs on the hitch assembly. 11. Close the hood, and lock the draw latch over the draw latch keeper on the hitch assembly. 10 - Husqvarna Deck Height Adjustment ASSEMBLY DRIVE PULLEY 1. Remove the discharge chute from the deck. (Deck configuration will vary by size and model) 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. 4. Relieve the tension from the deck belt and remove from the center deck pulley. (See Operator’s Manual if necessary) Discharge Chute Belt Cover 5. Remove the nut that secures the right hand deck Drive Pulley pulley to the spindle. 6. Install drive pulley included in collection system kit on top of the current deck pulley. 7. Reinstall the nut on the spindle and torque to 55- 75 ft/lbs. 8. Reinstall the deck belt. DECK STOP 1. Locate the deck stop behind the rear lift link on each side of the deck. 2. Set deck stop tube on the deck stop on each side. Deck Stop Tube Deck Stop Lift Link Husqvarna - 11 ASSEMBLY BLOWER ASSEMBLY 1. Position blower over the discharge tabs on the deck and set blower onto the deck. 2. Be sure the blower is sitting flush against the outside of the deck. 3. Secure the mount bracket to the deck with the pin and hairpin cotter supplied with the kit. Mount Bracket Pin Discharge Tab DRIVE BELT 1. Make sure the tension release lever is forward or disengaged. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release arm to the rear and engage in the latch. Rear Of Deck Idler Pulleys Outer Pulley Twist in Belt Tension Release Arm 12 - Husqvarna ASSEMBLY MIDDLE CHUTE BLOWER ASSEMBLY MIDDLE CHUTE 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. BELT COVERS 1. Place the deck belt shield on the deck over the drive pulley and secure with hardware removed from steel belt shield. 2. Place retainer on the outer pulley cover. 3. Align the tab end of the belt cover into the slot on the deck belt shield and the other end over the end of the outer pulley cover. 4. Secure with knob. Retainer Knob Outer Pulley Cover Deck Belt Shield Belt Cover Tab Middle Chute Latch Husqvarna - 13 ASSEMBLY 2. BOLT 3. BOLT WEIGHT BRACKET CAST WEIGHT WEIGHT KIT 1. Bolt cast weight and two weight brackets together using 2." bolts and nuts. 2. Slide both weight brackets over the front tube on the frame, positioning the assembly in the center of the frame. 3. Secure with 3." bolts and nuts. FRONT TUBE SERVICE AND MAINTENANCE TRANSPORT STORAGE When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a c...