Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
7. Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly. ¦ Disposal When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. US-8 HEZ2450S/HEZ3050S 6. Set up (B) (A) SE1 SE2 ¦ MOUNTING OTHER PARTS 1. Insert the driveshaft into the clutch drum, then attach the gearbox to the shaft tube as aligning the positioning holes and fasten the screw (A). Fasten the clamp bolt (B) firmly. (SE1) (A) Screw (B) Clamp bolt (B) Tightning Torque: 70~130 in-lb (8~15 N.m) 2. Install the handle to the shaft tube and clamp at a position best for your job. (SE2) U S US-9 [ R+M ] 2 50:1 MIXING CHART GASOLINE gal. 1 2 3 4 5 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 GASOLINE liter 1 2 3 4 5 2-CYCLE OIL ml 20 40 60 80 100 HEZ2450S/HEZ3050S 8. Operation ¦ STARTING ENGINE WARNING The RedMax stick edgers are designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. ¦ ADJUSTING WHEEL HEIGHT 1. Loosen the wing nut and change the wheel height to obtain desired cutting depth. (OP1) (1) Deep cut (2) Shallow cut (3) Wing nut 2. After adjusting the height, tighten the wing nut securely. Tightening Torque: 51~68in-lbs (6~8N.m.) OP2 (2) (3) (1) OP3 (1) (3) (a) (b) (2) OP4 OP5 The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflown fuel flows out in the clear tube. (OP2) 3. Move the choke lever to the closed position. (OP3) (1) choke lever (2) close (3) open 4. Set the stop switch to the "RUN" position. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. (OP4) (1) stop switch (2) RUN (3) STOP (a) lockout lever (b) throttle trigger 5. Firmly grasp (a) and (b) with left hand, pull the starter knob quickly until engine fires. (OP4,5) IMPORTANT • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6. Move the choke lever downward to open the choke. And restart engine. (OP3) 7. Allow the engine to warm up for several minutes before starting operation. (1) (2) (3) OP1 WARNING • Never adjust wheel height with the engine running. US-12 HEZ2450S/HEZ3050S 8. Operation ¦ HOW TO USE NOTE WARNING 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. ¦ STOPPING ENGINE (OP4) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the stop switch to the "STOP" position. IMPORTANT U S 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the blade guard and the mad guard attached in place at all times when the unit is operated. 3. Before starting a job, check the area and remove all obstacles and objects that could be thrown by the blade. 4. Do not adjust the wheel height or try to remove anything entangled to the blade with the engine running. 1. Before starting the engine, adjust the wheel height for desired cutting depth (See page 12). 2. Before starting a job, plan your direction of travel so that you can always hold the edger on you right side and can walk on a hard surface as much as possible. 3. When starting to edge, maintain the engine speed at the level required to perform edging work, and slowly have the blade cut into the edge groove. OP8 • Except for an emergency, avoid stopping the engine while pulling the throttle lever. ¦ ADJUSTING THROTTLE CABLE • The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP6) (1) cable adjuster ¦ ADJUSTING IDLING SPEED (OP7) 1. When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise. 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise. (1) idle adjusting screw (1) OP7 .04 in (1~2mm) (1) OP6 NOTE • Before edging, make sure the area is soft enough so the blade does not bog down. • Do not move the edger into the work so fast that the engine or blade bogs down. • Do not operate using starting throttle lock. It may cause unit uncontrolled, and clutch failure. • Use care indirecting discharge to avoid bystanders, vehicles, glass, and the like. • When the blade guard is clogged or blade stuck, stop the engine and clean it. NOTE • Warm up the eng...
Other models in this manual:Lawn Mowers - STICK HEZ2450S (395.4 kb)