Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
2 multipurpose lithium grease. Alignment couplings 251H EP grease or equivalent No. 2 multipurpose lithium grease. 35 LUBRICATION GUIDE A WARNING The life of any machine depends upon the care it is given. Proper lubrication is a very important part of that care. Be certain that all lubrication fittings are assembled in place, using the lubrication illustrations as a guide. Always lubricate the tractor thoroughly before taking it to the field. Use a pressure lubricating gun. Be sure all fittings are free from dirt and paint so the lubricant is certain to enter the bearing. Always force the lubricant through the full length of each bearing until it emerges at the end, carrying with it the worn lubricant and any dirt that may have entered the bearing. Miscellaneous working parts not provided with lubrication fittings should be oiled daily with a good grade of lubricating oil. Lubricant is cheap. Use plenty of it. Worn parts can be expensive to replace. Keep your supply of lubricating oil and grease stored in clean containers, and covered to protect from dust and dirt. Keep the lubricating gun nozzle clean and wipe dirt from grease fittings before lubricating. The symbols in the illustration indicate the method of application and the hourly intervals to apply the lubricant. Use a pressure lubricating gun and apply 251H EP grease (or equivalent No. 2 multi-purpose lithium grease) sufficient to flush out the old grease and dirt. Lubricate at hourly intervals indicated on symbols. Dipstick, use to check engine oil before each use. 36 LUBRICATION GUIDE 1. Engine filler cap and dipstick 2. Steering knuckles (2) (Both sides) 3. Front axle pivot bolt (Right side) 4. Drive shaft bushing 5. Front wheel bearings 6. Engine oil drain plug and oil filter Transmission 7. Oil level and filler plug 8. Oil drain plug Creeper drive housing 9. Level plug 10. Breather and filler plug 11. Drain plug 12. Steering gear housing Miscellaneous Brake pedal shaft Alignment couplings —Before Each Use Check the oil (with the engine stopped) and add sufficient new oil to bring it to the "FULL" mark on the dipstick. Do not overfill. Do not operate the engine if the oil level is below the "LOW" mark on the dipstick. -After Every 10 Hours of Operation Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease and apply sufficient grease to flush out old grease and dirt. NOTE: It may be necessary to rotate the front axle to reach the grease fitting. -After Every 30 Hours of Operation Two or three strokes of the lubricator using 251H EP grease or equivalent No. 2 multi-purpose lithium grease. Two or three strokes minimum of the lubricator using 251H EP grease or equivalent No. 2 multi-purpose lithium grease. -After Every 50 Hours of Operation While the engine oil is warm, remove the drain plug and oil filter (5), and drain all of the oil from the crankcase and oil filter lines. Replace the drain plug. Refer to "MAINTENANCE," "FILLING THE CRANKCASE" & "OIL FILTER" for proper oil filling procedure. Refer to "LUBRICATION TABLE" for the proper quantity and viscosity to use. ■After Every 100 Hours of Operation Check the oil level at the beginning and end of each season. Keep the lubricant up to "FULL" on dipstick. Check the oil level at the beginning and end of each season. Every 100 hours of yearly use 251H EP grease or equivalent No. 2 multi-purpose lithium grease. Apply two strokes with lubricator. Lubricate the brake pedal shaft and linkage with eight or ten drops of engine oil. Use 251H EP grease or equivalent No. 2 multi-purpose lithium grease. NOTE Lubrication information for optional equipment may be found in the manual which is included with the specific piece of optional equipment. AT 5 HOURS AND EVERY 50 HOURS THEREAFTER LUBRICATION GUIDE SPECIFICATIONS CAPACITIES Fuel tank ..................................................... Crankcase ................................................... Transmission case...................................... Steering gear housing................................. TRANSMISSION GEARS Speed: 1st................................................... 2nd .................................................. 3rd................................................... Reverse.......................................... CREEPER SPEEDS 1st................................................... 2nd ................................................. 3rd ................................................... Reverse.......................................... ENGINE Make and model......................................... (electric starting)......................................... Cylinders .................................................... Bore............................................................ Stroke.............