Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle, Should the trans- axle ever leak or require servicing, contact a Sears or other qualified service center. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL Select the oil's SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30, t 0W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°R Check your engine oil level more frequent ly to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before start ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level. TO CHANGE ENGINE OIL Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. 1. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. 2. Remove yellow cap from end of drain valve and install the drain tube onto the fitting. Oil Drain Valve Closed and Locked Position Drain Tube 2O 3. Unlock drain valve by pushing inward slightly and turning counterclockwise. 4. To open, pull out on the drain valve. 5. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. 6. Remove the drain tube and replace the cap onto the end of the drain valve. 7. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. 8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL' line on dipstick. Tighten cap onto the tube securely when finished. ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. AIR FILTER Your engine will not run properly using a dirty air filter. Replace pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. 1. Pull up on air filter cover handle and rotate towards engine. 2. Remove cover. 3. Carefully remove air filter cartridge and pre-cleaner from base. 4. Clean base carefully to prevent debris from falling into carburetor. NOTE: If very dirty or damaged, replace cartridge. 5. Place new pre-cleaner and cartridge firmly in base. 6. Align tabs on cover with slots in blower housing and replace cover. 7. Hook handle on cover and push down on handle to close. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean cartridge. ii / CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE COOLING SYSTEM Debris may clog the engine's air cooling system. Remove blower housing and clean area shown to prevent overheating and engine damage. Air Screen Clean out chaff and debris 21 MUFFLER CLEANING Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" section of this manual. IN-LINE FUEL FILTER The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. 1. With engine cool, remove filter and plug fuel line sections. 2. Place new fuel filter in position in fuel line with arrow pointing towards carburetor. 3. Be sure there are no fuel line leaks and clamps are properly positioned. 4. Immediately wipe up any spilled gasoline. Fuel Filter • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces w...