Votes - 2, Average rating: 4 ( )

Manafacture: Echo File size: 1.34 mb File name: Language of manual:

DO NOT let handle snap back or damage to unit will occur. 14. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITh CATALyST -The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 15. FUEL TANK - Contains fuel and fuel filter. 16. FUEL TANK CAP - Cover and seals fuel tank. 17. ChOKE - The choke control is located on the air filter case. Move lever to "COLD START" ( ) to close choke for cold starting. Move lever to "RUN" ( ) position to open choke. 18. AIR CLEANER ASSEMbLy -Contains replaceable felt element. 19. PURGE bULb - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times. 10 contents The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. ___ 1, Power Head ___ 1, Drive Shaft Assembly ___ 1, Plastic Bag (Co-Pack) ___ 1, Operator's Manual ___ 1, Safety Manual ___ 1, Warranty Registration Card ___ 1, Front Handle ___ 1, Lower Bracket, Front Handle ___ 4, 5 x 35 mm screws ___ 1, T-Wrench ___ 1, Torx T27 L-Wrench (PE-265S Only) ___ 2, Split pin ___ 1, 4 mm Hexagon Wrench ___ 1, Locking Tool ___ 1, 8 x 10 mm Spanner Wrench ___ 1, Safety Glasses assembly Tools Required: 4 mm Hex Wrench, 8 x 10 mm Open-end Wrench Parts Required: Power head, Drive Shaft Assembly drIve shaft/power head 1. Stand power head upright on a level surface. 2. Loosen the two (2) drive shaft clamp bolts (B) at engine drive shaft clamp, and remove center drive shaft location bolt (A). 3. Remove dust cap and carefully fit drive shaft assembly to engine making sure that inner drive shaft engages into clutch mount. 4. Turn drive shaft housing until locating hole lines up with location hole in clamp and install center drive shaft location bolt (A). NOTE Gear Housing must be aligned properly with engine. Aligning center locating hole in driveshaft housing with center drive shaft bolt (A) provides correct alignment. a B B Power edger oPerator's Manual 11 5. Tighten two (2) drive shaft clamp bolts (B) securely. 6. Route throttle linkage and ignition lead assembly along shaft and clip as shown. a B B throttle lInkage and IgnItIon leads 1. Close choke and remove air filter cover. 2. Place throttle linkage (C) through adjustment fixture (D) and install wire end into large carburetor throttle swivel hole (E). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. The throttle linkage must be adjusted by moving the adjustment fixture (D). Consult with your Echo Dealer for correct adjustment procedure. 3. Connect 2 ignition stop leads (F, G) from throttle cable tubing to 2 ignition leads (F, G) on engine. 4. Secure ignition leads against engine housing with clip (H). 5. Install air filter and cover. C D E g F H H 12 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. fuel warningAlternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. front handle Tools Required: Torx T27 L-Wrench Parts Required: Front Handle, Lower Bracket, 4 - 5 x 35 mm screws NOTE Label shows minimum spacing for front handle location. 1. Assemble front handle and bracket loosely to drive shaft. 2. Position front handle in comfortable operating position and tighten screws. Min SPaCing warningMoving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. operatIon warningOperation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor and a spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements. Power edger oPerator's Manual 13 Fuel Req...

Download now

Please, enter two numbers from picture: