Votes - , Average rating: ( )

User manual Poulan, model 96072001100

Manafacture: Poulan
File size: 721.05 kb
File name:

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

03021 LOWER CHUTE ATTACHING STRAPS PARTS IDENTIFICATION UPPER CHUTE CHUTE LATCH FULL BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS COVER ASSEMBLY UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Assembly (1) Cover Assembly 5 1 BAGGER SUPPORT ASSEMBLY (See Fig. 1) 1. Slide fl anges of support assembly into drawbar slots fi rst, then, pivot backwards inserting pin into drawbar pin hole. 2. Be sure support assembly is seated properly, then secure with retainer spring. 2 FIG. 1 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting coverassembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 2 03024 COVER ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY 02543 INSERT FLANGES FIRST INTO DRAWBAR SLOTS SUPPORT ASSEMBLY DRAWBAR SLOTS RETAINER SPRING PIN 02051 02051 02051 DRAWBAR PIN HOLE CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donot operatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 6 LOWER CHUTE (See Fig. 5) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower and position lower chute over mower opening as shown. 3. Hook rear latch into fl ange hole on back of mower. 4. Hook front latch into tab hole on front of mower. • If your tractor is equipped with gauge wheels on the deck, then it will be necessary to hook the rear latch into the hole in the R.H. gauge wheel bracket. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. WARNING Donotoperatemowerunlesscontainer isproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged. Useonlyarecommendedreplacementcontainer. WARNING Donotoperate mowerunlesscontainer isproperlyis nstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged. Useonlyarecommendedreplacementcontainer. 03022 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 4 FIG. 4 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES 03058 DEFLECTOR SHIELD HINGE BRACKET REAR LATCH REAR GAUGE WHEEL BRACKET DEFLECTOR SHIELD FRONT LATCH WITHOUT REAR LATCH GAUGE WHEELS WITH REAR GAUGE WHEELS EXTENDED EDGE "B" Must be under defl ector shield and along side the hinge bracket FIG. 5 TAB 7 03029 UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger indicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 6 COVER HANDLE LOWER CHUTE FULL BAGGER UPPER INDICATOR CHUTE FIG. 6B FIG. 6A 03023 BOSSES LATCH PIN ALIGNMENT SLOT RUBBER LATCH LEVEL MOWER • Be sure mower is properly leveled for best mower per for man ce. See your tractors owner's manual for ins truc tions 7 OPERATION TIPS FOR IMPROVED BAGGING OPE RATION: Follow the mower operation instructions in your tractor owner's manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of you...