Votes - 3, Average rating: 5 ( )

Manafacture: Electrolux File size: 762.96 kb File name: Language of manual:

Insert the nuts into the lower handle wing knobs. (A1) 2. Place the hole in the lower handle over the end of the tie rod (A) 3. Place the washer and wing knob onto the end of the tie rod and firmly tighten. (A) 4. Repeat on the other side. Assembly of Upper Handles to Lower Handles. 1. Insert the nuts into the upper handle wing knobs. (B1) 2. Ensure the upper handle and the lower handle are aligned correctly. (B) 3. Fit the bolts, washers and wing knobs..(B) 4. Fit the cable to the handles with the clips provided, making sure the cables are not trapped between the upper and lower handles. Assembly of Switchbox to Upper Handle 1. Insert the studs in the switchbox hinge into the holes in the upper handle as illustrated in Fig C 2. Firmly secure with the two screws (D). Grassbox Assembly. 1. Insert the grassbox handle into the grassbox upper, as illustrated in fig E, and press firmly down until the handle clicks into place - (if applicable). 2. Align the grassbox upper with the grassbox lower. 3. Locate the clips in the order illustrated in Fig F, ensuring all the clips are firmly in place. Adjusting the Cutting Height Cutting Height Adjustment (G) and (H) HEIGHT OF CUT WHEELS POSITION Low Front position 1 • Height of cut is adjusted by raising or lowering Back position 1 the wheels. Low to Medium Front position 1 • There are five heights of cut on this product. Back position 2 • NOTE Medium Front position 2 A medium height of cut is recommended for Back position 2 most lawns. The quality of your lawn will suffer and Medium to High Front position 2 collection will be poor if you cut too low. Back position 3 High Front position 3 Back position 3 Grassbox Fitting Fully Assembled Grassbox to Lawnmower. See Fig J. 1. Lift safety flap. 2. Make sure the discharge chute is clean and free from debris. 3. Locate fully assembled grassbox onto the location point at the rear of the deck (J1) 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. Ensure the Safety Flap is fully closed. The design of the safety flap permits the cut grass to be discharged downward behind the machine. ENGLISH - 2 Starting and Stopping To Start your Lawnmower 1. Connect female extension cable connector to the back of the switchbox. 2. Connect plug to mains and switch on. 3. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button (K1) to prevent accidental starting. 4. Press and hold the lock off button on the switchbox,(K1) then squeeze the Start/Stop lever towards the upper handle as shown on Fig. L. 5. Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button.(M) 6. Lower the lawnmower to its proper operating position and commence mowing. To Stop your Lawnmower 1. Release the pressure on the Start/Stop lever. How to Mow 1. For the best results, mow the outside edge of the lawn in a clockwise direction first.(N1) 2. Then start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (N2) 3. For best grass collection, always mow in a straight line, do not swing the lawnmower from side to side. Do Not Overload Your Mower Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection. Removing and Fitting the Blade and Fan P1 - Blade bolt P2 - Blade P3 - Fan • Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade and Fan 1. To remove the blade bolt, hold the fan firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise (P). 2. Remove the blade bolt, blade and fan. (P) 3. Inspect for damage and clean as necessary. • Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. • If the blade is cracked or damaged replace it with a new one. • Never use a blade bolt if the insulated head is damaged cracked or missing. Fitting the Blade and Fan 1. Ensure the fan is located correctly.(P) 2. Fit the blade to the fan with the tilt edges of the blade (P4) facing towards the mower, ensuring the blade is located onto the fan location points (P5) correctly 3. Re-assemble blade bolt through blade and fan. 4. Hold the fan firmly and tig...

Download now

Please, enter two numbers from picture: