Votes - 3, Average rating: 3.7 ( )

Manafacture: Craftsman File size: 609.13 kb File name: Language of manual:

Repeat for all four plugs. STEP 4: (SEE FIGURE 5) • Attach ]eft mounting bracket to hole shown in ]eft side of tractor frame using a carriage bolt (A) and whizlock nut (C). Align middle hole in bracket with empty hole in tractor frame. Tighten whizlock nut (C) only enough to keep bracket in alignment until step 5. Repeat for right mounting bracket. STEP 5: (SEE FIGURE 6) • Fasten bumper to mounting bracket using a hex bolt (B), pivot spacer (E), a locking lever and a whizlock nut (C) as shown. The pivot spacer inserts into hole in bumper. Tighten both nuts on mounting bracket at this time. Repeat for other side. • Assemble plastic grips (F) onto locking levers. • Lift up on bumper until pins in locking levers snap into holes in mounting brackets. IMPORTANT: You must lower bumper before raising tractor hood. Pull out on locking levers and push bumper down as far as it will go. STEP 6: (SEE FIGURE 7) • Replace the front screws and browning shield you removed in Step 2 as shown. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH OR SOLID TABL__ (GT) FRAME SHOWN CARRIAGE LEFT MOUNTING BUMPER STOPS BOLT (A) BRACKET FACE OUT .......... WHIZLOCK NUT (C) AUGNROLES TRESE I I LEFT SIDE VIEW FIGURE 5 HEX BOLT (B) WHIZLOCK_ (C) PIVOT SPACER (E)_ LEVER GRIP (F) FIGURE 6 LEFT SIDE VIEW REPLACE FRONT SCREWS REPLACE BROWNING SHIELD FIGURE 7 LEFT SIDE VIEW 4 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE INSTRUCTIONS FOR DUAL SUSPENSION BRACKET TRACTORS STEP 1 : (SEE FIGURE 2) Open parts bags labelled "A" and "B" and verify that all parts are present. NOTE: Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. CAUTION! Muffler is hot! Allow engine to cool down before proceeding with bumper installation. NOTE: Right hand (RH) and left hand (LH) are determined from the operator's position while seated on the tractor. STEP 2: (SEE FIGURE 3) Remove tractor hood. (Refer to tractor manual.) Place hood on cardboard or on a mat to protect paint. If you have an (LT) Lawn Tractor with a heat shield like the one shown, remove the heat shield. iMPORTANT: Be sure to re-attach the heat shield after bumper is installed. Catt 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE SHOWN FULL SiZE PARTS BAG "B" EXCEPT WHERE NOTED (parts bag "A") E J D (parts bag "A") (parts bag "A") (parts bag "A") FIGURE 2 REF PART NO. QT_ DESCRiPTiON A 48894 2 SelfThreadingScrew,3/8-16x 1-1/2" B 43062 2 Hex Bolt, 3/8-16 x 1-1/2" C 43001 2 Hex Bolt, 3/8-16 x 1" D 48866 2 Pivot Spacer E 1643-60 2 Plastic Grip F 43003 4 Lock Washer, 3/8" G 43070 4 Washer, 3/8" H 44742 4 Plug (LT) LAWN TRACTOR ......... -----1 MUFFLER HEAT SHIELD ) N FIGURE 3 5 STEP 3: (SEE FIGURE 4) • Place plug (H) on a work bench or solid table and push end of bumper down onto plug. Repeat for all four plugs. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH OR SOLID TABLE _/PLUG (H) FIGURE 4 STEP 4: (SEE FIGURE 5) IMPORTANT: Do not remove any bolts from the tractor frame while the mower deck is raised. Misalignment of holes in frame could result. (LT) LAWN REMOVE BOLT IF PRESENT TRACTOR Lower mower deck to rest on ground. Remove bolts from mounting holes on both sides of tractor frame. Use a mounting bracket to help identify holes. SUSPENSION BRACKET (LT) LAWN TRACTOR REMOVE BOLT IF PRESENT \ // J SUSPENSION BRACKET (GT) GARDEN TRACTOR ...

Download now

Please, enter two numbers from picture: