Votes - 3, Average rating: 3
(
)
)
|
manual abstract
1. Remove the filler cap/dipstick and wipe it clean. 2. Insert and remove the dipstick without screwing it into the filler opening. Check the oil level shown on the dipstick. OIL LEVEL 3.If the oil level is low, fill to the edge of the oil filler hole with the recommended oil (see page 21). To avoid overfilling or underfilling, be sure the engine is in a level position, as shown. NOTICE Engine Oil Change FILLER OPENING Drain the used oil while the engine is warm. Warm oil drains quickly and completely. 1. Place a suitable container below the engine to catch the used oil, then remove the filler cap/dipstick and drain the used oil through the filler opening. Allow the used oil to drain completely. NOTICE Improper disposal of engine oil can be harmful to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground. 2. With the engine in an upright position, fill to the edge of the oil filler hole with the recommended oil (see page 21). Engine oil capacity: 3.38 fl oz (0.11US qt, 100 cc) 3. Tighten the oil filler cap/dipstick securely. Running the engine with too little or too much oil can cause engine damage. 4. Tighten the oil filler cap/dipstick securely. SERVICING YOUR HONDA STICK EDGER Engine Oil Recommendations Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for all temperatures within the recommended operating range for these stick edgers. The recommended operating range extends from 23°F (-5°C) to 104°F (40°C). The SAE oil viscosity and service classification are on the API label on the oil container. Honda recommends that you use API SERVICE category SH or SJ oil. Air Filter Inspection Squeeze the air cleaner latch tabs, and remove the air cleaner cover. Check the filter to be sure it is clean and in good condition. If the filter is dirty, clean it as described in the next section. Replace the filter if it is damaged. Reinstall the filter and air cleaner cover. NOTICE Cleaning A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the engine in very dusty areas, clean the air filter more often than specified in the MAINTENANCE SCHEDULE. FILTER AIR CLEANER COVER LATCH TABS RETAINING TABS Operating the engine without an air filter, or with 1. Clean the air filter in warm soapy water, a damaged air filter, will allow dirt to enter the rinse, and allow to dry thoroughly. Or clean engine, causing rapid engine wear. This type of in nonflammable solvent and allow to dry. damage is not covered by the Distributor's 2. Dip the air filter in clean engine oil, then Limited Warranty. squeeze out all excess oil. The engine will smoke when started if too much oil is left in the filter. 3. Wipe dirt from the air cleaner base and cover using a moist rag. Be careful to prevent dirt from entering the carburetor. SERVICING YOUR HONDA STICK EDGER Spark Plug Service Recommended spark plugs: CR5HSB (NGK) U16FSR-UB (DENSO) NOTICE An incorrect spark plug can cause engine damage. SPARK PLUG SPARK PLUG CAP 1. Disconnect the spark plug cap, and remove any dirt from around the spark plug area. 2. Remove the spark plug with a 5/8-inch spark plug wrench. 3. Inspect the spark plug. Replace it if the electrodes are worn, or if the insulator is cracked or chipped. SIDE ELECTRODE 0.024 - 0.028 in (0.60 - 0.70 mm) 4. Measure the spark plug electrode gap with a suitable gauge. The gap should be 0.024 ~ 0.028 in (0.60 ~ 0.70 mm). Correct the gap, if necessary, by carefully bending the side electrode. 5. Install the spark plug carefully, by hand, to avoid cross-threading. 6. After the spark plug seats, tighten with a 5/8 inch spark plug wrench to compress the washer. If reinstalling the used spark plug, tighten 1/8 ~ 1/4 turn after the spark plug seats. If installing a new spark plug, tighten 1/2 turn after the spark plug seats. NOTICE A loose spark plug can overheat and damage the engine. Overtightening the spark plug can damage the threads in the cylinder head. 7. Attach the spark plug cap. SERVICING YOUR HONDA STICK EDGER Spark Arrester Service The spark arrester must be serviced every 100 hours to keep it functioning as designed. If the engine has been running, the muffler will be very hot. Allow the muffler to cool before servicing the spark arrester. RECOIL STARTER 5 x 18 mm BOLTS 1. Remove the four 5 x 18 mm bolts from the recoil starter, and remove the recoil starter. TOP COVER 5 x 22 mm BOLTS 3. Remove the two 5 x 22 mm bolts from the top cover, and remove the top cover. 2. Disconnect the spark plug cap from the spark plug. Pull the spark plug wire and the ignition switch wire out of the retainers in the top cover. RETAINERS SPARK PLUG CAP SPARK PLUG WIRE IGNITION SWITCH WIRE 4. Remove the three 5 mm screws from the muffler cover, and remove the muffler cover....