Votes - 3, Average rating: 3.7 ( )

Manafacture: Flymo File size: 707.62 kb File name: 7a784d39-7959-42af-b4bf-6812b191b152.pdf Language of manual:

14. Do not put hands near the grass discharge chute. 15. Never pick up or carry a mower when it is operating or still connected to the mains supply. STOP 16. Remove the plug from the mains : -before leaving the mower unattended for any period; -before clearing a blockage; -before checking, cleaning or working on the appli- ance; -if you hit an object. Do not use your lawnmower until you are sure that the entire lawnmower is in a safe operating condition.; -if the lawnmower starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury. Maintenance and storage 1. Keep all nuts, bolts and screws tight to be sure the lawnmower is in safe working condition. 2. Check the grassbox frequently for wear or deterioration. 3. Replace worn or damaged parts for safety. 4. Only use the replacement blade, blade bolt, spacer and impeller specified for this product. 5. Be careful during adjustment of the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the machine. CABLES IMPORTANT • Use only 1.00mm2 size cable up to 40 metres length maximum. Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. • YOUR LAWNMOWER IS SUPPLIED WITH AN ELECTRIC MAINS CABLE FITTED WITH A FEMALE CONNECTOR. 1. Flymo Mains Cables and Extension Cables are available from your local Electrolux Outdoor Products Approved Service Centre. 2. Do not wire an extension cable directly to your prod- uct yourself. Please contact your local Electrolux Outdoor Products Approved Service Centre for fur- ther information on the connectors and kits avail- able. 3. Only use extension cables specifically designed for outdoor use. CONNECTORS IMPORTANT • Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. • All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be sub- merged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT IMPORTANT • If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 1. No earth required. Flymo products are double insulat- ed to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE -NEUTRAL BROWN -LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped cor- rectly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only pro- tect the electrical equipment and are not a safe- guard against electrocution. E L F U S EN BLACK OR BLUE RED OR BROWN Assembly Instructions E L F U S EN BLACK OR BLUE RED OR BROWN Assembly Instructions A1 A2 B1 B2ensure the point of the screw stays inside the han- dle C1 C2 Wheel Assembly (if not already fitted) (A1, A2) 1. Select one of the holes in the mounting plate and note it as the other wheels will need to be adjusted to the same position. (A1) 2. Locate the fixing bolt through hole in the hub cap, wheel and selected hole in mounting plate. 3. Turn the wheel hub in a clockwise direction until the wheel assembly is securely located to the deck. (A2) Lower Handle Assembly - Venturer 370 (B1, B2) 1. Locate 2 screws into the holes in the handles. 2. Using a pozidrive screwdriver, secure the screws into the lower handles, ensuring the point of the screw stays inside the handle. (B1) 3. Insert lower handles, with screws attached, into the deck and fully tighten screws. (B2) Note: The screw will form its own thread Lower Handle Assembly - RE420/420c (C1, C2) 1. If your product has Cutting Height with levers (see Cutting Height Adjustment), ensure the lever is at the Highest Cut Height before following steps 2 & 3. 2. Insert lower handles into deck as shown in Fig C1. 3. Push each handle firmly down until it is located securely into the deck (C2). 4. Insert screw through the washer and into holes using a pozidrive screwdriver and tighten fully into deck as shown in Fig C2. Fitting Upper Handles to Lower Handles (D & E) 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost 2. Ensure the upper handle and the lower handle are aligned correctly. 3. Insert the nut into the handle knob. (if applicable) (D1) 4. Fit the bolts, washers and handle knobs. 5. Fit the cable to the handles with the cli...

Download now

Please, enter two numbers from picture: