Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Discard the support flange if it is cracked. • Ensure that the nut has not lost its tightening capacity. The nut lock shall have a locking torque of at least l.5 Nm. The nut’s tightening torque shall be 35-50 Nm. • Check that the blade and blade guard are not damaged or cracked. Replace the blade or blade guard if it has been exposed to impact or if it is cracked. 8 – English English – 9 Lubricating the flexible drive axle Inside the edger‘s drive shaft is a flexible drive axle. The flexible drive axle should be regularly lubricated after 30 hours of operation. Loosen the two screws on the angle gear and remove it. The flexible drive axle is easily removed from the shaft by taking a firm grip on the axle end. Lubricate the flexible drive axle over its entire length and reinsert it in the shaft. Turn the axle while inserting it so that it correctly engages in the clutch. Replace the angle gear on the drive axle shaft and tighten the two screws. MAINTENANCE The cutting depth should be adjusted before starting work. • Loosen the locking handle (A) and rotate the guard by moving the locking knob forwards or backwards. If the locking handle is moved forwards (from the machine) the cutting depth is increased. If the locking handle is moved backwards (towards the machine) the cutting depth is reduced. • Adjust the cutting depth. • Lock the locking handle. A WARNING! Always bear the machine on the right side of the body. Always wear protective glasses, long trousers and heavy-duty shoes when using the machine. Observe your surroundings, ensure people and animals do not come in the immediate vicinity or can be hit by thrown objects. Apply full throttle before the blade starts to work on the soil. ! Adjusting the edger's cutting depth Angle gear The angle gear is filled a sufficient quantity of grease at the factory. However, before using the machine you should check that the angle gear is filled to 3/4 with grease. Use HUSQVARNA special grease. Normally, the grease does not need to be changed except when repairs are carried out. Maintenance schedule Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Check that the blade does not rotate while idling. 2. Check the guard for damage and ensure that it is not cracked. Replace the guard if it has been exposed to impact or is cracked. 3. Check that the blade is undamaged and not cracked. Replace the blade if necessary. 4. Check that the locking nut is tight. 2 3 4 1 Weekly maintenance 1. Check that the angle gear is 3/4 filled with grease. Fill if necessary using special grease. 2. The flexible drive shaft must be lubricated after every 30 hours in operation or more often. 1 2 TECHNICAL DATA Technical data Weight, Lbs/kg Blade length Centre hole, blade Speed, blade 1,6 195 mm 1" = 25,4 mm 7140 r/min EXPLICATION DES SYMBOLES Symboles AVERTISSEMENT! Le tranchebordure peut etre dangereux! Une utilisation negligee ou incorrecte peut entrainer des blessures graves, voire mortelles pour l'utilisateur ou d'autres personnes. Lire attentivement le manuel d'utilisation et assimiler son contenu avant d'utiliser la machine. Toujours porter: • Un casque de protection en cas de risque de chute d'objets. • Des protege-oreilles • Des lunettes de protection homologuees max Regime max. de l'arbre sortant, tr.min 10000 rpm Ce produit est conforme aux directives CE en vigueur. Attention aux objets projetes et aux ricochets. 50FT15 m50FT15 m Attention a la lame en rotation. Surveiller les pieds et les mains. Attention! La lame continue a tourner, meme apres l'arret du moteur. Lorsque le moteur est arrete, arreter la lame en l'amenant en contact avec le sol. Indique le sens de rotation. L'utilisateur de la machine doit s'assurer qu'aucune personne ou animal ne s'approchent a moins de 15 metres pendant le travail. Fleches indicatrices indiquant les limites pour l’emplacement de la fixation de la poignee. Toujours porter des gants de protection homologues. Porter des bottes solides et antiderapantes. Les autres symboles/autocollants presents sur la machine concernent des exigences de certification specifiques a certains marches. Controles et/ou entretiens doivent etre effectues avec le moteur arrete et le contacteur d'arret en position STOP. Toujours porter des gants homologues. La machine demande un entretien regulier. Controle visuel. Toujours porter des lunettes de protection homologuees. 10 – Francais SOMMAIRE Husqvarna AB travaille continuellement au developpement de ses produits et se reserve le droit d’en modifier, entre autres, la conception et l’aspect. Lire attentivement le manuel d’utlilisation et assimiler son contenu avant d’utiliser la machine. Ces instructions son un complement au manuel qui accompagne la machine. Pour les autres instructions, se reporter au manuel d.utilisation de la machine. ! ! AVERTISSEMENT! En aucun cas, la conception d'origine de la machine ne doit etre modifiee sans ...