Votes - 2, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
Half-press the shutter button. This will cause the camera to start pre-recording images. • The camera will not emit a shutter sound when you half-press the shutter button while Prerecord CS is selected. • If you release the half-pressed shutter button before pressing it the rest of the way down, all of the pre-recorded images currently in the buffer will be deleted. 15. When you are ready to shoot, press the shutter button the rest of the way down. This will record the images in the pre-record buffer and start recording new images in real-time. Images continue to be shot as long as you keep the shutter button depressed. 16. Real-time shooting will stop when you release the shutter button or after the maximum number of shots is reached. 17. Save the CS images (page 54). NOTE • Note the following when selecting a High Speed CS speed (fps) setting. – Use a higher High Speed CS speed (fps) setting when shooting a fast-moving subject. – Use a slower High Speed CS speed (fps) setting when shooting a slower-moving subject. • Note the following when selecting a High Speed CS maximum number of shots setting. – The greater the number of shots, the longer it takes to save them after shooting is complete. • Note the following when specifying a Prerecord CS shots setting. – A setting that results in a Prerecord CS operation that takes at least 0.3 seconds is recommended because there is a minimal lag from about 0.1 seconds to 0.3 seconds between the point you decide to shoot and the point that the shutter button is fully depressed. Snapshot Tutorial 53 Specifying the Method for Saving Continuous Shutter Images Use the procedure below to specify how images should be saved after a High Speed CS operation. 1. In the REC mode, press [MENU]. 2. Use [4] and [6] to select the “REC” tab. 3. Use [8] and [2] to select “Save CS Images”, and then press [6]. 4. Use [8] and [2] to change the setting. Normal (Batch) All images that were shot are saved after the continuous shutter operation is finished. Snapshot Tutorial 54 Select & Save After continuous shutter shooting is finished, the shot images are played back at slow speed so you can select the images you want to save. • When shooting with Prerecord CS, the first image saved when you press the shutter all the way is indicated by an “S” mark so you can tell where the continuous shutter operation started. 1While the shot images are playing back and an image Mark appears that you want to save, press the shutter button. Each image that you select by pressing the shutter button will have a mark appended to it. 2After selecting all of the images you want to save, press [MENU]. Buttons Used for Image Selection [4] [6] During playback, these buttons change the playback direction and playback speed. While playback is paused, these buttons scroll forward or back. [SET] Toggles between pause and play. Shutter button Press all the way down to select an image for saving. [MENU] Saves the selected images and exits the image select operation. 3Use [8] and [2] to select the save method you want and then press [SET]. Save All : Saves all the images. Save Selected : Saves selected images. Back : Returns to image selection. Cancel Save : Does not save any of the images. Always Ask After continuous shutter shooting is finished, a prompt appears allowing you to select Normal (Batch) or Select & Save. Select the save method you want to use and then press [SET]. Save Selected : Saves selected images. Save All : Saves all the images. Cancel Save : Does not save any of the images. 5. Press [SET] to apply the setting. Snapshot Tutorial 55 Continuous Shutter Precautions • If there is not enough available capacity on the memory card, you may not be able to record the number of CS images indicated on the monitor screen. Make sure your memory card has sufficient remaining capacity before shooting with using continuous shutter. • With continuous shutter, exposure and focus for the first image are applied for successive images as well. • When using a continuous shutter mode, keep the camera still until shooting is finished. • In the Continuous Shutter mode, the flash setting automatically becomes ? (Flash Off). • Zoom is disabled during continuous shutter operations. • The following image sizes cannot be selected while shooting with High Speed CS: “10M”, “3:2”, “16:9”. Entering the High Speed CS mode while any one of these image sizes is selected will cause the image size setting to change to “9M” automatically. • The maximum number of images that can be recorded during each High Speed CS session is limited, regardless of how much memory card storage capacity is available. High Speed CS Specified maximum number of continuous shutter shots (Max CS shots)S The number of images will be restricted even further or shooting may be impossible when remaining memory card capacity is less than the allowable number of images for a particular CS mode. • The Triple Self-time cannot be used in the High Speed CS mode. • The S...