Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
Before plugging in, read the information about dual voltage contained in the instruction section of this manual. 17. This appliance was set at the factory to operate at 125 volts. Refer to the following section of this manual for conversion to 250 volts operation. SAVE THESE INSTRUCTIONS OPERATING INSTRUCTIONS This appliance is intended for household use only. Use on Alternating Current (50/60 Hz) only. This dryer is designed to operate at 110/125 or 220/250 volts AC. This appliance was set at the factory to operate at 110/125 volts. Make sure the dual voltage selector is in correct voltage position before operating. Before plugging in, read the information about dual voltage contained in the instruction section of this manual. For Dual Voltage Dryers For use in the U.S.A., the voltage selector switch should be placed in the 125 position. For use in several countries overseas, the voltage selector may need to be placed in the 250 position. Confirm the voltage available at each overseas location before using the appliance. For connection to a 250 volt supply, use an attachment plug adapter of the proper configuration for the power supply receptacle. For 110-125 Volt Operation Flick the dual voltage switch to the 125 position. In this position, the dryer operates on all available heat and speed settings. For 220-250 Volt Operation Unplug the unit. The switch should be set at OFF position. Change the dual voltage switch to the 250 position. Operate the unit between LOW and OFF settings only. At 250V setting, the unit will operate at high speed/high heat. When at 250V setting, do not attempt to select high setting or change the dual voltage switch to 125 position. A plug adapter may be necessary in certain countries. Additional information This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. CHECK ALCI SAFETY FEATURE EVERY TIME YOU USE APPLIANCE. This appliance is equipped with an Appliance Leakage Circuit Interrupter (ALCI), a safety feature that renders it inoperable under some abnormal conditions, such as immersion in water. To make sure the ALCI is functioning properly, perform the following test. The purpose of this test is to allow you to make sure the water sensing system (ALCI) is working. 1. Plug in the appliance and press test button on plug (see appropriate diagram below). 2. The appliance will stop working. There will be an audible click and reset button will pop out. 3. To reset ALCI with a reset button, unit should be unplugged. Then push reset button in, and reinsert plug into outlet. 4. If ALCI is not functioning properly, return appliance to nearest service center. 5. It is important that if immersion occurs, this unit be brought to a service center. Do not try to reset. 6. Be sure to repeat test every time you use the unit to confirm ALCI is operational. Should the appliance go off and the reset button pop up during use, this could indicate a malfunction in the unit. Remove plug from outlet and allow the appliance to cool. Reinsert plug into outlet. The appliance should then function normally. If not, return to an authorized Conair Service Center for evaluation and repair. SUPER STYLING GUIDE Your best looks begin with a good haircut that’s well maintained. Always treat hair right with superior quality shampoos, conditioners, and finishing products. DRYING BASICS 1. Shampoo and condition hair with products of your choice. Rinse thoroughly. Towel-dry hair to remove excess moisture. Using the dryer along with your styling brush, start at a lower setting and direct hot air through a section of hair at a time. Move dryer steadily across each section so that the hot air passes through hair. Direct air flow at hair, not scalp. Natural ions generated by the Tourmaline Ceramic™ heat will help to reduce static Reset Test Reset Test electricity, control frizzy flyaways and contribute to your hair’s shine. 2. Keep dryer’s air intake vents unobstructed and free from hair while drying. 3. To avoid over-drying, do not concentrate heat on any one section for any length of time. Keep dryer moving as you style. 4. For quick touch-ups between shampoos, dampen hair with a mist of water before styling with the dryer. 5. When using your dryer to create curls and waves, dry hair almost completely on a warmer temperature setting, then finish styling with cool setting to close hair shaft and lock in style GETTING TO KNOW YOUR DRYER The Conair® Mini Pro Tourmaline Ceramic™ Styler is very effective, even at lower temperatures, and helps to give healthier-looking, shiny, more manageable hair with maximum styling control. BODY & VOLUME To create extra volume, turn head upside down while drying. Position the air flow toward the roots for maximum lift. When hair ...