If it does not work, see TROUBLESHOOTING. 4. Use back cover of push button as a template to mark two screw holes. 5. Drill two holes with 3/32” size drill in marked locations. 6. Secure back cover to the mounting surface with two supplied mounting screws. 7. Press front housing onto back cover. 8. Test operation. If the chime does not work, see TROUBLESHOOTING. Operation 1. Slide power switch to “High” or “Low” to power the chime. 2. Gently press transmitter button to sound chime. Troubleshootin

3. Remove the battery pack and discard appropriately. Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips screwdriver. Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (for anchors) (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with jumpers 7-9. Si

Turn off power. Attach one wire to each of the screw terminals on the back of the button. Mount button in desired location with two screws provided. Install according to applicable local electrical codes. -EEL Wall

1. Remove the battery from the push button transmitter. 2. Locate the 3 dip switches shown below. 3. Select the desired chime sound from the table below. ON: Switch On OFF: Switch Off - Chime Dip Switches(Ding Dong Shown) House Code Jumpers Chime Dip Switches(Ding Dong Shown) House Code Jumpers Pushbutton Dip Switches and Jumpers Setting The House Security Code Each chime component has 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings f

Take care not to scratch the glass surface. Do not use abrasive cleaners. CAUTION: THE CST-38 AND CPF-38 FIREPLACES MUST BE OPERATED WITH THE GLASS DOORS FULLY CLOSED. IMPORTANT These glass doors utilize tempered glass which is designed for use with high temperatures but can unexpectedly shatter. DO NOT SIT CLOSE TO THE GLASS. Tempered glass will break into small particles if it should shatter unexpectedly. If the glass breaks, particles of extremely hot glass could be discharged into the surrou

Additionally these doors are designed for use with the Merit Plus Series, Models CST-38 and CPF-38. Do not alter or modify these door assemblies or a fireplace malfunction or a fire hazard may result. Models 38ABF(BB/BS) have been tested and listed by Omni Test Laboratories, Inc. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. GENERAL INFORMATION This door assembly consists of a right and left glass panel assembly with the door handles factory mounted. There are no additional parts that are requ

Slide the door panel on the hinge pin until the gap between the upper door trim and upper frame is even. Retighten the lower door hinge pin*. Repeat this procedure for the opposite door if needed. *Note: Upper door hinge pins can also be loosened for adjustment purposes; however, it is easier to loosen lower pins. GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH THE SUPERIOR FIREPLACE OR APPLIANCE MODELS SHOWN. USE ON ANY OTHER FIREPLACE OR A

DO NOT SIT CLOSE TO THE GLASS. Tempered glass will break into small particles if it should shatter unexpectedly. If the glass breaks, particles of extremely hot glass could be discharged into the surrounding environment, thereby creating a risk of personal injury or fire. Observation of the above operating precautions and instructions will reduce the risk of personal injury or fire. Extreme temperature changes can cause breakage — do not build a hot fire and close the doors if the doors are cold

Lennox's Symphony series Bi-Fold doors come standard with a decorator satin black finish and may be purchased in a polished brass finish designated by the -B suffix to the model/size number. Do not alter or modify these door assemblies or a fireplace malfunction or a fire hazard may result. These glass door assemblies have been tested and listed by Warnock Hersey Inc. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. GENERAL INFORMATION This door assembly consists of a right and left bi-fold glass

Step 2. Position the frame in the fireplace opening on top of the door support bracket, centering left and right. Mark the fireplace at each hole in the side panels. Note:The frame is provided with two sets of holes allowing for near "Flush Face" installation and "Protruding" installations that may be particularly useful in certain finish applications. In most cases the door frame will not install completely flush with the appliance front face. The frame will usually protrude from the opening ap