Login:
Votes - 4, Average rating: 3.8 ( )

User manual Invacare, model 1090768

Manafacture: Invacare
File size: 41.04 kb
File name: 1092333.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


1090768 Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage before using. In case of damage, DO NOT use. Contact the Dealer/ Carrier for further instructions. SAFETY SUMMARY The following recommendations are made for the safe installation of the Lock Handle Assembly Kit (Kit No. 1090768). This kit is used where Roll Pin (Part No. 1079151) is used with Right Hand Lock Handle (Part No.1068937) and Left Hand Lock Handle (Part No. 1068938). GENERAL WARNING DO NOT assemble or use this kit without first reading and understanding this instruction sheet. If you are unable to understand the Warnings, Cautions or Instructions in this Instruction Sheet contact a healthcare professional, dealer or technical personnel before attempting to install this kit, otherwise, injury or damage may occur. INSTALLATION WARNINGS After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. NOTE: Refer to the GENERAL WARNINGS in the SAFETY SUMMARY of this Instruction Sheet. Installing Handle Lock Assembly (Figure 1) 1. Locate bushing arm lock and determine if EXISTING handle lock and/or the EXISTING roll pin are present. 2. If EXISTING handle lock and/or EXISTING roll pin is present, remove by tapping out the roll pin using a center punch - otherwise proceed to STEP 3. 3. Slide EXISTING spring on to the narrow end of the EXISTING coil pin (If necessary). 4. Insert the EXISTING coil pin and spring into the bushing arm lock as shown in FIGURE 1. 5. The NEW handle lock is placed on to the EXISTING coil pin and bushing arm lock. 6. Ensure hole in the EXISTING coil pin is aligned with holes in the NEW handle lock, insert tubular rivet through NEW handle lock and EXISTING coil pin as in FIGURE 1 DETAIL "A". NOTE: If unable to insert tubular rivet due to frame interference or otherwise, push the existing coil pin so that the narrow end of the existing coil pin is visible at the other end of the bushing arm lock and can be rotated to allow the tubular rivet to be inserted through both the new handle lock and the existing coil pin. (constant pressure will be needed on the coil pin to insert in this manner). 7. Head end of tubular rivet is butted against a hard flat surface and lightly tap the end of the center punch into the hollowed end of the tubular rivet causing it to "spread" (DETAIL "B"). WARNING When installing the tubular rivet ensure the hollow end is evenly "spread" and secures the handle lock. DO NOT use excessive force when installing the tubular rivet - otherwise the handle lock may not function properly. NOTE: it is recommended that STEP 7 be performed on a work bench or similar structure. If the head end of the tubular rivet can not be butted against a hard flat surface due to frame interference or otherwise, use a solid object (piece of metal, tool handle, ect...) that fits the space between the head end of tubular rivet and the frame interference or otherwise to hold rivet in place. 8. Repeat steps 1-7 on remaining bushing handle lock. This kit contains the following: DESCRIPTION *QTY Handle Lock (Right Hand) 1 Handle Lock (Left Hand) 1 Tubular Rivet 2 *NOTE: These quantities are per kit. 1 DETAIL "A" (Narrow End) Tubular Rivet Hollowed End Handle Lock INVACARE CORPORATION • ONE INVACARE WAY • ELYRIA, OH 44035 Customer Service (800) 333-6900 • Technical Support (800) 832-4707 Form No. 99-186 Part No. 1092333 Rev. A (1) - 8/99 Printed in USA...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category