Votes - , Average rating:
(
)
)
Manafacture: Ives
File size: 94 kb
File name: 551f7777-5dde-4c42-997b-c57cc3a1f88a.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Position jamb bracket 1/4" in from door and fasten to doorframe (see illustration below) .Open side of bracket must be facing screen or storm — 2. Slide the "hold open" washer onto rod. Use short connecting pin to connect closer to jamb bracket. The “hold open" washer should be placed over lugs against closer tube (see illustration below). This will provide proper tension for installation and should not be adjusted until installation is complete. 3. Use long connecting pin to attach door bracket to closer tube. Tightly close and latch door and hold closer and door bracket in level position. Mark and drill two 1/8" diameter pilot holes. Fasten to door with short screws provided (see illustration below). 4. Open door and move "hold open" washer behind lugs on rod. The closing speed can be regulated by turning the adjusting screw (see illustration below). If less closing power is required, hold door open about 8“ with "hold open" washer, remove long connecting pin and relocate in rear hole. Jamb Brai Door Frame (Jamb) Long .Connecting Pin —■ 926 PNEUMATIC DOOR CLOSER £) "©<=£> UE-pE- INSTALLATION INSTRUCTIONS (Use of a little oil or soap on threads makes driving screws much easier.) THIS CLOSER MAY BE INSTALLED ON RAIL AT TOP OF DOOR OR ON MULLION STRIP NEAR CENTER, WHICHEVER IS DESIRED NOTE: BEFORE INSTALLATION, CHECK DOOR TO SEE THAT IT CLOSES FREELY (USE 1/T DRILL BIT FOR ALL PILOT HOLES) % STEP 1 At desired height, fasten jamb bracket to door frame with open side 1/4" from door as shown. (See Fig. A) If more latching force is desired, jamb bracket may be moved up to 1" away from door. NOTE: Moving the jamb bracket further from door nominally reduces door opening. STEP 2 Slide hold-open washer on rod. Using short connecting pin, connect closer to jamb bracket. Hold-open washer should be positioned over lugs against closer tube as shown. This will give proper tension for installation. (Do not change until installation is completed.) (See Fig. B) STEP 3 Two styles of door brackets are made. (See Fig. C & Fig. D) Your closer comes with only one. Attach door bracket to closer tube FRONT hole with long connecting pin (see Fig. C or Fig. D). With door tightly closed, hold closer and door bracket against door in level position, mark and drill two 1/8" pilot holes. CAUTION: Do not drill through door. Fasten door bracket to door as shown with short screws (see Fig. C or Fig. D) Open door and move hold-open washer back of lugs on rod. Closer is now ready to operate. The closing speed may be regulated by turning adjusting screw (see Fig. E). CONTROLLED LATCHING POWER FEATURE Installed as directed, with the door bracket attached to the front hole of the door closer, the bypass valve built into this closer will accelerate the closing speed of the door in the last few inches of travel. This attachment position is recommended when the glass storm panel is in place. If a smoother, more quiet closing action is desired, hold door open about 8" with hold-open washer, remove long connecting pin from door bracket and relocate in closer tube REAR hole. This position is normally used when the screen panel is in place (see Fig. C or Fig. D). FIG. A FOR HEAD JAMB BRACKETS G*«* type o' o»a<*ei ^cmaed A Top Jamb ■Overhead ’ Bracket Place Ove'heao B'kW apamst Stle Jamb and 3.V troro face 0» 0oo> Wdh door dosed, hold end oi rod on top o» bracket and «sen pn Spread spfci end si HOLD OPEN WASHER LUG FIG. C DOOR BRACKET V LONG CONNECTING PIN «.REAR HOLE ^ y 'ADJUSTING SHORT SCREWS^FRONT HOLESCREW FIG. 0 LONG CONNECTING PIN DOOR BRACKET SHORTSCREWS REAR HOLE ADJUSTING SCREW FRONT HOLE FIG. E ADJUSTING SCREW DOOR FRAME (JAMB) H.B. IVES, a Harrow Company 62 Barnes Park North P.O. Box 5035 Wallingford, CT 06492 Phone:203-294-4837 Fax:203-284-1460 MADE IN U.S.A....