Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
In typical use, alkaline batteries will last up to one year. Case Style "A" 1. Install alkaline type A23 12 volt pushbutton battery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 3). Case Style "B" 3. Install 2 alkaline "C" batteries. Make sure batteries are oriented properly. 2.Open chime case. Press in catch on bot- tom of chime and lift the case open. 12345678 Battery Battery 4.Test range. Temporarily position chime and pushbutton where you want them mounted. Press pushbutton to verify chime and pushbutton work properly. If chime does not sound, see Troubleshooting. 5. Mount pushbutton and chime. Use either screws or double sided tape to mount pushbutton. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. © 2003 DESA Specialty Products™ 595-5551-09 Keyhole 1 9/16" Holes for Wall Mounting Keyhole 1 9/16" Holes for Wall Mounting Attach back of case to door jamb or wall. Snap front of pushbutton on. When attaching pushbutton using double sided tape, make sure the surface of the door jamb or wall is clean. Case Style "A": Chime can be mounted by us ing 2 holes in the back of case, or by using 1 screw with keyhole. Case Style "B": Chime can be mounted by using 1 screw with keyhole (see illustration on page 1). Case Style "A": Snap front of chime case on. Start with top edge of case aligned with the top of back plate. Case Style "B": Snap battery access door firmly in place before mounting (See illustration on page 1). Case Style "A" Back Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and pushbutton. The pushbutton and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the pushbutton and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Open the cases and locate the jumpers on both the pushbutton and chime (See illustration on page 3). 2. The pushbutton and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the pushbutton and chime for this system to function. -2-595-5551-09 Tune Settings Your wireless chime has different selectable tunes: Ding (one note), Ding- Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Pushbutton: Add a jumper to location 8. • Ding-Dong (two note tune) Pushbutton: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Pushbutton: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. We recommend the back door use the Ding tune and the front door use the Ding- Dong tune (or Westminster tune, available on selected chimes). Models that include two pushbuttons will come factory set for front and back doors. Decals on the rear of the pushbutton will indicate its setting. BatteryBattery 12 345 678 Pushbutton Battery Replacement Install an alkaline type A23 12 Volt battery. The positive terminal should be positioned as shown. * Code Settings 1-7 Must Match Both Pushbutton and Chime Inside Pushbutton Inside Chime Tune Setting (Not used on all models) Tune Setting 12 345 678 Note: Some models might require the use of tweezers to remove and replace the jumpers. 595-5551-09 -3 Troubleshooting Chime doesn't sound: • Make sure pushbutton and chime codes are the same (See pages 2 and 3). • Check orientation of pushbutton battery (See page 3). • Check charge of pushbutton and chime batteries, replace if necessary. Batteries seem OK, but the chime doesn't work when installed: • Don't mount chime or pushbutton on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or pushbutton off metal surface. • Concrete floors may reduce range. Move chime away from floor. •Try locating chime closer to pushbutton. The range of the wireless chime can vary with location, temperature and battery condition. Technical Service (Do Not Send Products) If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1800- 858-8501, 7:30 AM to 4:30 PM CST (M...