Votes - 2, Average rating: 4
(
)
)
|
manual abstract
, and “ on the front display panel won’t stop blinking. . The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. . The end of the tape was reached during timer recording. ]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. blinks for 10 seconds and the timer mode is disengaged. . # has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. ]Check the programmed data and re-program as necessary, then press # again. The SHOWVIEW system does not timer-record properly. . The unit’s channel positions have been set incorrectly. ]Refer to “SHOWVIEW TM Timer Programming” (. pg. 24) and re-perform the procedure. and “ on the front display panel won’t stop blinking. . The end of the tape was reached during Instant Timer Recording. ]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. , and “ on the front display panel won’t stop blinking. . The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. . The end of the tape was reached during Automatic Satellite Programme Recording. ]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. . The camcorder’s microphone is too close to the TV. ]Position the camcorder so its microphone is away from the TV. . The TV’s volume is too high. ]Turn the TV’s volume down. When scanning channels, some of them are skipped over. . Those channels have been designated to be skipped. ]If you need the skipped channels, restore them. (. pg. 60) The channel cannot be changed. . Recording is in progress. ]Press 9to pause the recording, change channels, then press 4 to resume recording. Channel settings that were made manually seem to have changed or disappeared. . After the manual settings were made, Auto Channel Set was performed. ]Perform the manual settings again. No channels are stored in the unit s memory. . The TV aerial cable was not connected to the unit when Auto Set Up was performed. ]Turn off the unit once and connect the TV aerial cable to the unit properly, then turn on the unit again. Then perform Auto Set Up again. (. pg. 10) . The fully-wired 21-pin SCART cable was not connected between the TV and the unit when Preset Download was performed. ]Turn off the unit once and connect the fully-wired 21-pin SCART cable to the unit properly, then turn on the unit again. Then perform Preset Download again. (. pg. 12) ATTENTION This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the mains power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette, operate the unit as usual. Page 69 October 9, 2004 10:34 pm Filename [XV48EX_EN_11Trouble.fm] Masterpage:Left0 XV48EX_EN_01.book Page 70 Saturday, October 9, 2004 10:34 PM 70 EN SPECIFICATIONS GENERAL Power requirement : AC 220 V – 240 V , 50 Hz/60 Hz Power consumption Power on :23 W Power off : 4.0 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 435 mmx 93 mmx 272mm Weight : 4.2 kg Format : VHS PAL standard Maximum recording time (SP) : 240 min. with E-240 video cassette (LP) : 480 min. with E-240 video cassette VIDEO/AUDIO (VHS deck) Signal system : PAL-type colour signal and CCIR monochrome signal, 625 lines 50 fields Recording system : DA4 (Double Azimuth) head helical scan system Signal-to-noise ratio: 45 dB Horizontal resolution : 250 lines Frequency range : 70 Hz to 10,000 Hz (Normal audio) 20 Hz to 20,000 Hz (Hi-Fi audio) Input/Output : 21-pin SCART connectors: IN/OUT x 1, IN/DECODER x 1 RCA connectors: VIDEO IN x 1, AUDIO IN x 1, AUDIO OUT x 1 VIDEO/AUDIO (DVD deck) Signal system : PAL Applicable disc : DVD VIDEO, DVD-R (Video format), DVD-RW (Video format), Video CD, SVCD, Audio CD (CDDA), CD-R/RW (CD-DA, Video CD, SVCD, MP3 format, JPEG, DivX) Frequency responce DVD :4 Hz– 22 KHz CD :4 Hz– 20 KHz S/N Ratio : 90 dB Wow and flutter : Below Measurable Level Dynamic range : 90 dB Output Audio : (RCA) 2 Vrms, 1 Kohm Digital Audio : –21 dBm to –15 dBm (peak) TUNER/TIMER (VHS deck) TV channel storage capacity : 99 positions (+AUX position) Tuning system : Frequency synthesized tuner Channel coverage : VHF 47 MHz – 89 MHz/ 104 MHz – 300 MHz/ 302 MHz – 470 MHz UHF 470 MHz – 862 MHz Aerial output : UHF channels 22 – 69 (Adjustable) Memory backup time : Approx. 10 min. ACCESSORIES Provided accessories : RF cable, Infrared remote control unit, “R6” battery x 2 Specifications ...