Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
To connect your player to a television: If your TV is high-definition or digital ready, you may take advantage of the player’s progressive scan output for the best possible video output. • Progressive scan does not work with the analog video connections (yellow VIDEO-OUT jack). • The 720p and 480p resolutions are the progressive scan applied resolutions. 1 Make sure the DVD player is connected directly to the TV and not to a VCR. Failure to connect the player properly will cause the DVD image to be distorted by the copy protection system. Insignia NS-1UCDVD DVD Player 2 Plug the audio/video cables from the DVD player’s jacks to the TV as follows: Cable Connect on player to: Connect on tv to: S-video cable (S) S-VIDEO OUT S-VIDEO IN Video Cable (V) VIDEO OUT VIDEO IN Audio Cable (A) AUDIO OUT AUDIO IN (left and right) Y PB PR Cable (C) COMPONENT/PROGRESSIVE SCAN Corresponding TV jacks Note Connecting both the S-video and component cables may cause the TV display to be unstable. To resolve the problem, disconnect one of the problems. Connecting your player to an HDMI TV High Definition Multimedia Interface (HDMI) supports both video and audio on a single digital connection for use with DVD players, set-top boxes, and other AV devices. HDMI was developed to provide the technologies of High-bandwidth Digital Content Protection (HDCP). HDCP is used to protect both transmitted and received digital content. HDMI has the capability to support standard, enhanced or high-definition video plus standard to multi-channel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs. Note HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. To connect your player to an HDMI device: 1 Set the source on your HDMI TV or monitor to HDMI as instructed in the owner’s manual. 2 Connect the HDMI OUT jack on the DVD player to the HDMI jack on your HDMI TV or monitor using an HDMI cable (H). The arrow on the cable connector body should face up for correct alignment with the connector on the player. 3 Press RESOLUTION repeatedly to select the desired resolution. When you use an HDMI connection, you can change the resolution (480i, 480p, 720p, 1080i) for the HDMI output. The HDMI output will have a resolution of 480p, even if you set the resolution to 480i on the HDMI connection. When no sound or noisy sound result from the HDMI connection, set the Audio option [Dolby Digital, DTS or MPEG] on SETUP menu to PCM or Off. Notes If there is noise or lines on the screen, check the HDMI cable. Not all HDCP-compatible DVI devices will work with this player. If your HDMI TV does not support HDCP, the screen is blue in color. If the TV picture is abnormal, turn off the unit and then turn the unit on again. Both PCM and Bitstream Audio out is available when the sample frequency is set to 48kHz in HDMI connection. If Audio setup is set to bitstream and your TV does not support Bitstream Audio out when using an HDMI connection, there may be no audio sound or sound may not be distorted. Setting the resolution If your TV does not accept your resolution setting, the tv picture displays abnormally. Refer to the owner’s manual for your TV to set the correct resolution. To set the resolution: 1 Press the STOP button to stop playback and put the player in stop mode. 2 Press the RESOLUTION button once. The current resolution displays in the window. 3 Press the RESOLUTION button repeatedly to change to the desired resolution. Available resolutions according to the connections include: Output connection Available resolution HDMI VIDEO OUT 1920 x 1080i 1280 x 720p 720 x 480p 720 x 480i COMPONENT VIDEO OUT 1920 x 1080i 1280 x 720p 720 x 480p 720 x 480i VIDEO OUT 720 x 480i 720 x 480p S-VIDEO 720 x 480i • For Video and S-VIDEO connections, resolution must be set to 480i or 480p; however, VIDEO OUT is always at 480i standard resolution. • For 720p and 1080i resolution on the component video out, only non-copy protected discs can be played back.If the disc is copy protected, it will be displayed at the 480p resolution without HDMI cable connection. With HDMI cable connection, the picture may not be display properly. Connecting your player to optional audio equipment You can connect your player to an external source to enjoy high quality stereo sound from your DVD player. Note This DVD player has been manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc. Rear of DVD player Amplifier (Receiver) To connect your player to optional audio equipment: 1 Amplifier equipped with 2-channel analog stereo or Dolby Pro Logic ...