Votes - 1, Average rating: 5
(
)
)
|
manual abstract
TV Control Buttons: You can control the sound level, input source, and power switch of your TV. Setting up the remote to control your TV You can operate your TV with the supplied remote control. If your TV is listed in the table below, set the appropriate manufacturer code. While holding down TV POWER button, and press the manufacturer code for your TV with the numerical buttons (see the table below). Release the TV POWER button to complete setting. Manufacturer Code Number LG / GoldStar 1 (Default), 2 Zenith 1, 3, 4 Samsung 6, 7 Sony 8, 9 Hitachi 4 Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. 7 Main Unit RH387H/RH388H/RH389H a b c d efghijk lmn RH397H/RH398H/RH399H ab jck a 1 11/ I (POWER button) Switches the unit ON or OFF. b Disc Tray Insert a disc here. c OPEN/CLOSE ( Z) Opens or closes the disc tray. d Display window Shows the current status of the unit. T/S: Indicates the timeshift mode. REC: The unit is recording. HDD: The unit is HDD mode. DVD: The unit is DVD mode. HDD bBDVD: The unit is dubbing. d e fghi lm n : Indicates when the unit is in timer : Indicates clock, total playing time, elapsed chapter/track number, channel, etc. e Remote Sensor Point the remote control here. f N/ X(PLAY / PAUSE) Starts playback. Pause playback or recording temporarily, press again to exit pause mode. g x(STOP) Stops playback or recording. h z(REC) Starts recording. Press repeatedly to set the recording time. i RESOLUTION Sets the output resolution for HDMI and COMPONENT OUTPUT jacks. - HDMI: 576i, 576p, 720p, 1080i, 1080p - COMPONENT: 576i, 576p j DVD Set the recorder’s mode to DVD. k HDD Set the recorder’s mode to HDD. l USB Port Connect an USB Flash Drive. m DV IN Connect the DV output of a digital camcorder. n AV IN 3 (VIDEO IN/AUDIO IN (Left/Right)) Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.). 8 9 Hooking up the unit aAntenna connection Connect the Terrestrial TV antenna to the ANTENNA IN jack on the unit. bAntenna connection to your TV Connect one end of the RF cable to ANTENNA OUT jack on the unit and other end to ANTENNA IN jack on your TV. Passes the signal from the ANTENNA IN jack to your TV/monitor. cSCART connection Connect one end of the scart cable into the AV1 SCART jack on the unit and other end to the corresponding in jack on your TV. You can get Audio and Video signals together with this connection. dPower cord connection Connect the mains lead to the AC IN terminal on the unit. Then plug the power cord into the mains. RH387H-S-BAUTLLX-ENG 6/16/11 3:00 PM Page 9 10 Hooking up the unit - more you can do Component connection Connect one end of the component(Y PB PR) cable to the COMPONENT OUTPUT jack on the unit and other end to the COMPONENT INPUT jack on your TV. Connect one ends of the audio cables (red and white) to the analog AUDIO OUTPUT jack on the unit and other ends to the AUDIO INPUT jack on your TV. If your television is a high-definition or “digital ready” television, you may take advantage of the unit’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled with the progressive signal. Set the resolution to 576p using RES. button on the front panel to obtain the progressive signal. S-Video connection Connect one end of the S-Video cable to the S-VIDEO OUTPUT jack on the unit and the other end to the S-VIDEO INPUT jack on your TV. Connect one ends of the audio cables (red and white) to the analog AUDIO OUTPUT jack on the unit and the other ends to the AUDIO INPUT jack on your TV. Digital audio connection Connecting to an amplifier/receiver, Dolby Digital/MPEG/DTS decoder or other equipment with a digital input. Connect one end of the digital audio cables (COAXIAL or OPTICAL) to the digital audio output jack (COAXIAL or OPTICAL) on the unit and other end to the digital audio input jack (COAXIAL or OPTICAL) on your amplifier. This recorder does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs. RH387H-S-BAUTLLX-ENG 6/16/11 3:00 PM Page 10 HDMI connection Connect one end of the HDMI cable jack on the unit and other end to the HDMI INPUT jack on your TV. Recorder TV When you use the HDMI connection, you can change the resolution (576i, 576p, 720p,1080i or 1080p) for the HDMI output by pressing RES. button repeatedly. About HDMI HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD Players, Set-Top Boxes, and other AV devices. HDMI was developed to provide the technologies of HDCP (High-ba...
Other models in this manual:DVD Players - RH388H (2.83 mb)