Votes - 0, Average rating: 0
(
)
)
|
manual abstract
8239 300 34302 17/12/2004, 10:24 AM Getting Started Step 1: Inserting batteries into the Remote Control 1 3 2 1 Open the battery compartment. 2 Insert two batteries type R06 or AA, following the indications (+-) inside the compartment. 3 Close the cover. Using the Remote Control to operate the Player 1 Aim the Remote Control directly at the remote sensor (IR) on the front panel. 2 Do not put any objects between the Remote Control and the DVD Player while operating the DVD Player. CAUTION! – Remove batteries if they are exhausted or if the Remote Control is not being used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed properly. 01-39 DVP3010_EU_00_2 15 Step 2: Setting up the TV IMPORTANT! Make sure you have completed all the necessary connections. (See pages 9-10 “Connecting TV”). 1 Turn on the TV and set to the correct video-in channel. You should see the Philips DVD background screen on the TV. 2 Usually these channels are between the lowest and highest channels and may be called FRONT, A/V IN, or VIDEO. See your TV manual for more details. . Or, you may go to channel 1 on your TV, then press the Channel down button repeatedly until you see the Video In channel. . Or, the TV Remote Control may have a button or switch that chooses different video modes. . Or, set the TV to channel 3 or 4 if you are using an RF modulator. 3 If you are using external equipment, (eg. audio system or receiver), turn it on and select the appropriate input source for the DVD Player output. Refer to the equipment owner’s manual for detail. 15 8239 300 34302 17/12/2004, 10:24 AM English Getting Started English Setting up Progressive Scan feature (for Progressive Scan TV only) The progressive scan display twice the number of frames per seconds than interlaced scanning (ordinary normal TV system). With nearly double the number of lines, progressive scan offers higher picture resolution and quality. IMPORTANT! Before enabling the progressive scan feature, you must ensure: 1) Your TV can accept progressive signals, a progressive scan TV is required. 2) You have connected the DVD player to your TV using Y Pb Pr (see page 10.) 1 Turn on your TV. 2 Turn off your TV progressive scan mode or turn on interlaced mode (refer to your TV user manual.) 3 Press POWER on the remote control to turn on the DVD player. 4 Select the correct Video Input channel. (See page 15). . The DVD background screen appears on the TV. 5 Press SYSTEM MENU. 6 Press 2 repeatedly to select {VIDEO SETUP PAGE}. Set P-SCAN On/Off - -Video Setup Page - - TV Type TV Display Progressive On Picture Setting Off Component 7 Select {PROGRESSIVE} to {ON}, then OK to confirm. . The instruction menu appears on the TV. 1) ENSURE YOUR TV HAS PROGRESSIVE SCAN. 2) CONNECT WITH YPBPR (GBR) VIDEO CABLE. 3) IF THERE IS A DISTORTED PICTURE, WAIT CancelOK ACTIVATING PROGRESSIVE: 15 SECONDS FOR AUTO RECOVERY. 8 Press 1 to highlight in the menu and press OK to confirm. OK There will be a distorted picture on your TV at this state until you turn on the progressive scan mode on your TV. 9 Turn on your TV progressive scan mode (refer to your TV user manual.) . The below menu appears on the TV. CONFIRM AGAIN TO USE PROGRESSIVE SCAN. IF THE PICTURE IS GOOD, PRESS OK BUTTON ON REMOTE CancelOK 0 Press 1 to highlight in the menu and press OK to confirm. OK . The set up is complete now and you can start enjoy the high quality picture. TIPS: To return to the previous menu, press 1. To remove the menu, press SYSTEM MENU. 16 8239 300 34302 01-39 DVP3010_EU_00_2 16 17/12/2004, 10:24 AM Getting Started To deactivate Progressive manually . When the distorted picture still appears on the TV, it may be due to the connected TV does not accept progressive signals, and progressive is set by mistake. You must reset the unit to interlace format. 1 Turn off your TV progressive scan mode or turn on to interlaced mode (refer to your TV user manual.) 2 Press OPEN/CLOSE on the DVD player to open the disc tray. 3 Press numeric keypad ‘1’ on the remote control for few seconds. . The DVD blue background screen will appear on the TV. Selecting the colour system that corresponds to your TV This DVD Player is compatible with both NTSC and PAL. In order for a DVD disc to play on this Player, the colour system of the Disc, the TV and the DVD Player should match. NTSC TV - -Video Setup Page - - TV Type PAL TV Display Multi Progressive NTSC Picture Setting Component 1 Press SYSTEM MENU. 2 Press 2 repeatedly to select {VIDEO SETUP PAGE}. 3 Press 3 4 to highlight {TV TYPE}, then press 2. 4 Press 3 4 to highlight one of the options below: PAL – Select this if the connected TV is PAL system. It will change the video signal of a NTSC disc and output in PAL format. NTSC – Select this if the connected TV is NTSC system. It will change the video signal of a PAL disc (VCD only) and output in NTSC format. Multi – Select this if t...