Votes - 0, Average rating: 0
(
)
)
|
manual abstract
10 Remote Control (continued) j DISC MENU – Enters or exits disc contents menu. – For VCD 2.0 and SVCD, turns on or off the playback control mode. k OK – Confirms an entry or selection. l RETURN/TITLE – Returns to the previous menu or shows title menu. m ./ > (Previous/Next) – Skips to the previous or next title/ chapter/track. – Press and hold this button for fast backward or forward search. n (USB) – Switches to USB mode and shows the content of the USB device. o SUBTITLE – Selects a DVD subtitle language. p ZOOM – Zoom the picture on the TV. q REPEAT – Selects various repeat modes; turns off repeat mode. REPEAT A-B – Repeat a specific section on a disc. 1011 121314 161715 English 11 Remote Control (continued) English Using the remote control CAUTION! – Remove batteries if they are exhausted or if the remote control is not to be used for a long time. – Never mix batteries (old and new or carbon and alkaline, etc.). – Batteries contain chemical substances; they should be disposed of properly. A Open the battery compartment. B Insert two batteries type R03 or AAA, following the indications (+-) inside the compartment. C Close the cover. D Point the remote control directly at the remote sensor (IR) on the front panel. Note: Never place any objects between the remote control and this unit while operating. E Select the desired function (for example u). 12 Basic Connections EnglishTV VIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT COAXIAL TV Video (yellow cable) TV VIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT COAXIAL DVD TV Audio (red/white cables) Step 1: Connecting to television This connection enables you to view the video playback from this unit. You only need to choose one of the options below to make the video connection. – For a standard TV, follow option 1 or 2. – For a progressive scan TV, follow option 3. Option 1: Using Scart socket (RGB) The scart cable provides both audio and video features with a single cable connection. • Connect the scart cable (not supplied) from the TV OUT socket on this unit to the scart input socket on your TV. Option 2: Using Composite Video sockets (CVBS) You can connect this unit to a TV through the composite video cable which provides good picture quality. • Connect the audio/video cables (not supplied) from the VIDEO OUT and AUDIO OUT L/R sockets on this unit to the video input socket (yellow) and audio input sockets (red/ white) on your TV. 13 Basic Connections (continued) EnglishVIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO DIGITAL OUT COAXIAL TV TV OUTVIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT COAXIAL 12Video Audio Option 3: Using Component Video sockets (Y Pb Pr) Step 2: Connecting the power cord You can connect this unit to a TV through the component video cables which provides superior picture quality. The progressive scan video quality is only available when using Y Pb Pr connection and a progressive scan TV is required. A Connect the component video cables (red/blue/green - not supplied) from the Y Pb Pr sockets on this unit to the corresponding component video input sockets (or labelled as Y Pb/Cb Pr/Cr or YUV) on your TV. B Connect the audio/video cable (not supplied) from the AUDIO OUT L/R sockets on this unit to the audio input sockets (red/white) on your TV. Leave the yellow video cable disconnected. C Proceed to ‘Getting Started - Setting up Progressive Scan feature’ for detailed progressive feature setup. After everything is connected properly, plug the AC power cord into the power outlet. Never make or change any connections with the power turned on. Helpful Hint: – Refer to the type plate at the rear or bottom of the product for identification and supply ratings. 14 Optional Connections EnglishVIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT COAXIAL AUDIO IN DIGITALSTEREOTV OUT AV Receiver Audio (red/white cables) VIDEO OUT Pb PrY COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT COAXIAL AUDIO IN DIGITAL Connecting to an Analogue Stereo System You can connect this unit to a two channel stereo system (e.g. mini system, analogue receiver) in order to enjoy stereo sound output. A Connect the audio/video cables (red/white - not supplied) from the AUDIO OUT L/R socket on this unit to the audio input sockets (red/white) on your connecting device. Leave the yellow video cable disconnected. B For video connection, see ‘Basic Connections - Step 1: Connecting to television’ for details. Helpful Hint: – See ‘Setup Menu Options - Audio Setup Page’ for optimum audio settings. Connecting to a Digital AV Amplifi er/Receiver You can connect this unit to an AV amplifier/receiver in order to enjoy quality sound. A Connect a coaxial cable (not supplied) from the COAXIAL DIGITAL OUT socket on this unit to the digital coaxial input socket of the connected device. B For video connection, see ‘Basic Connections - Step 1: Connecting to television’ for details. Helpful Hint: – You have to set the appropriate Digital Audio Output setting. ...