Votes - 3, Average rating: 3.7 ( )

Manafacture: Toshiba File size: 2.66 mb File name: Language of manual:

Close the cover. 1 Operating with the remote control Point the remote control at the remote sensor on the unit and press the buttons. Distance: About 7 m (23 feet) from the front of the remote sensor Angle: About 30° in each direction of the front of the remote sensor * Do not expose the remote sensor of the unit to a strong light source such as direct sunlight or other illumination. If you do so, you may not be able to operate the unit via the remote control. Notes on the remote control • Aim the remote control at the remote sensor of the unit. • Do not drop or give the remote control a shock. • Do not leave the remote control near an extremely hot or 2 3 Loading the remote control battery Within about 7 m (23 feet) 30°30° humid place. Notes on batteries • Do not spill water or put anything wet on the remote Improper use of batteries may cause battery leakage and control. corrosion. To operate the remote control correctly, follow the • Do not disassemble the remote control. instructions below. • Do not insert batteries into the remote control in the wrong direction. • Do not charge, heat, open, or short-circuit the batteries. Do not throw batteries into a fire. • Do not leave dead or exhausted batteries in the remote control. • Do not use different types of batteries together, or mix old and new batteries. • If you do not use the remote control for a long period of time, remove the batteries to avoid possible damage from battery corrosion. • If the remote control does not function correctly or if the operating range is reduced, replace all batteries with new ones. • If battery leakage occurs, wipe the battery liquid from the battery compartment, then insert new batteries. 15 Introduction Introduction Antenna Connection Connecting an antenna to this unit Connect the antenna to this unit for viewing broadcast signals. BITSTREAM/PCM OUT S-VIDEO IN VIDEO IN AUDIO INL R To VHF/UFH (75.) terminal VHF/UHF antenna Antenna cable (not supplied) Connecting to cable TV signal If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a two-set signal splitter (sometimes called a “two-set coupler”) and an A/B Switch box from the cable installer or an electronics supply store. Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 to 4) and use the box to tune scrambled channels. A B BITSTREAM/PCM OUT S-VIDEO IN VIDEO IN AUDIO INL R Converter/Descrambler Converter/Descrambler Splitter A/B Switch Incoming CATV 16 Power Connection Connect the supplied AC adapter to power the unit. Caution • Do not connect the power plug to a power outlet other than that indicated on the label, as this can result in a risk of fire or electric shock. • Do not connect or disconnect the power plug with wet hands. Doing so may cause electric shock. • Do not use an AC adapter other than one specified, as it can cause a fire or damage to the unit. • When the AC adapter is in use, its temperature may increase. However, it is not a malfunction. Make sure that the power cord is disconnected and the temperature decreases before carrying it. 2 PICTURE 1 3 To the DC IN jack AC adapter Connect the supplied AC adapter and the power cord firmly. Follow steps 1 to 3 to connect. When disconnecting, reverse this order. Power cord Power plug To wall outlet Introduction 17 18 Introduction How to use the main unit You can use the main unit in three ways. 1 Adjusting the direction of the LCD monitor Raise the switch located on the back of the LCD monitor. Push the LCD monitor forward. 2 Open the LCD monitor Firmly press down on the main unit to setup the LCD monitor. Open the LCD monitor. If the LCD monitor is opened more than 90 degrees, the main unit may overturn, so be careful. 90 degrees 1 2 IntroductionTo remove a disc Move the LCD monitor to the upward direction as shown below. Open the disc cover. Press OPEN on the main unit. The disc cover opens. • If the LCD monitor is not moved to the upward position and the disc cover is opened, the disc cover will hit against the LCD monitor and may break. OPEN How to use when hanging it on a wall You can use the main unit with the LCD monitor bent back 180 degrees. A professional will perform the wall installation. If you want to install the main unit this way, contact your local Toshiba sales department. 19 TV Viewing Settings for watching TV Channel Setting Selecting the Channel TV Viewing Settings for watching TV Channel Setting Selecting the Channel Settings the Sound Closed caption function/ V-CHIP function Adjusting the Picture TV Viewing TV Viewing POWER Settings for watching TV Steps for watching TV Turning on the power Turn on the power. Press the POWER button on the main unit. The unit turns on and the PO...

Download now

Please, enter two numbers from picture: