Votes - 4, Average rating: 4.3 ( )

Manafacture: Toshiba File size: 1.02 mb File name: Language of manual:

icon then press ENTER. JPEG JPEG Maintenance and Service Refer to the information in this chapter before contacting a service technician. HANDLING THE UNIT When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean • Do not use volatile liquids such as insecticide spray near the unit. • Do not leave rubber or plastic products in contact with the unit for a long period of time. since they leave marks on the surface. Cleaning the unit To clean the DVD Home Theater System, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Maintaining the Unit The DVD Home Theater System is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. Depending on the operating environment, regular inspection and maintenance are recommended after every 1,000 hours of use. For details, please contact your nearest authorized service center. 34 35 Operation Additional Features LAST SCENE MEMORY This receiver memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the receiver or switch off the receiver. If you load a disc that has the scene memorized, the scene is automatically recalled. Note: This receiver does not memorize the scene of a disc if you switch off the receiver before commencing to play the disc. VIDEO MODE SETTING • With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That means Vertical interpolation or De-interlace is not perfectly matched with the disc. In this case, the picture quality may be improved by changing the video mode. • To change the video mode, press and hold DISPLAY about 3 seconds during disc playback. The new video mode number selected is displayed on the TV screen. Check whether the video quality has improved. If not, repeat the above procedure until picture quality is improved. • Video mode change sequence: MODE1 >MODE2 >MODE3 >MODE1 • If you turn off the power, the video mode will be back to initial state (MODE1). Tip: Detailed Descriptions for Video Modes MODE1: The source material of the DVD video (film material or video material) is determined from disc information. MODE2: Suitable for playing film based content or video based material recorded by the progressive scan method. MODE3: Suitable for playing video based content with comparatively little motion. SLEEP TIMER SETTING You can set the DVD Home Theater System to turn off automatically at a specified time. 1. Press SLEEP to set the desired sleep time. The SLEEP indicator and sleep time appears in the display window. 2. Each time you press SLEEP the setting changes in the following order. SLEEP 180 >150 >120>90 >80 >70 >60>50 >40 > 30 >20 >10 >OFF Note: • You can check the time remaining before the DVD Home Theater System turns off. Press SLEEP. The remaining time appears in the display window. DIMMER This function will change the brightness of the display window on the front panel during in power-on status. Press the DIMMER repeatedly. MUTE Press MUTE to mute your unit. You can mute your unit in order, for example, to answer the telephone, “MUTE” indicator flashes in the display window. Press MUTE again to release it. USING HEADPHONE JACK Connect a stereo headphone plug ( 3.5mm) into the PHONES connector. The speakers are automatically disconnected when you plug in a headphone (not supplied). DVD 35 Operation Additional Features LAST SCENE MEMORY This receiver memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the receiver or switch off the receiver. If you load a disc that has the scene memorized, the scene is automatically recalled. Note: This receiver does not memorize the scene of a disc if you switch off the receiver before commencing to play the disc. VIDEO MODE SETTING • With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That means Vertical interpolation or De-interlace is not perfectly matched with the disc. In this case, the picture quality may be improved by changing the video mode. • To change the video mode, press and hold DISPLAY about 3 seconds during disc playback. The new video mode number selected is displayed on the TV screen. Check whether the video quality has improved. If not, repeat the above procedure until picture quality is improved. • Video mode change sequence: MODE1 >MODE2 >MODE3 >MODE1 • If you turn off the power, the video mode will be back to initial state (MODE1). Tip: Detailed Descriptions for Video Modes MODE1: The source material of the...

Download now

Please, enter two numbers from picture: