Votes - 6, Average rating: 4.5
(
)
)
|
manual abstract
5. Slow motion playback, Shuttle : During playing back or still picture press F or G. You can reach the following playback speeds. (REV, PB5-, PB1-, still, SLW, PLAY, 2PLY, CUE). To switch off the slow motion and shuttle, press the desired function. During slow motion and shuttle, the noise bars may appear on the picture according to the status of tape. If distortions can be seen in the picture, reduce them with TRK + or -. 6. Press STOP to end playback. Press EJECT. If the end of the tape is reached, your VCR will stop playback automatically, rewind, stop, eject the tape. CM (Commercial Message) Skip: This feature enables you during playback of a tape to skip a commercial break in a few seconds, then resume normal playback. While tape is playing press CM SKIP on the remote control to skip commercial (or another programme material). Repeatedly press CM SKIP to skip: 1 Press 30 seconds 2 Press 60 seconds 3 Press 90 seconds 4 Press 120 seconds 5 Press 150 seconds 6 Press 180 seconds OPR (Optimum Picture Response) This feature automatically improves playback picture quality by adjusting your VCR to the condition of the tape. Please note that the OPR icon ( ) will only appear in play that mode when playing a tape. 1. Press i. 2. Press 1 or 2 to select OPR. 3. Press OK. 4. Press 33 or 44 repeatedly to select: OFF, SOFT or SHARP. Please note you may only set OPR when playing a tape. 5. Press i return to screen. 12 SET ON OFF OSDfOFF SOFT SHARP Recording Your VCR allows you to make recordings connecting to a TV equipped with audio out and video out sockets. Your VCR start recording immediately for a set period of time (ITR : Instant Timer Recording) or until the video cassette runs out. Your VCR incorporates Long Play (LP) which enables you to record up to twice the amount of time on a video cassette. For example an E-180 will record up to 180 minutes using Standard Play (SP); using LP you will be able to record up to 360 minutes. Please note there will be a slight loss in picture and sound quality when using LP. 1. Connect the AUDIO(L/R)/VIDEO (VCR IN AV1) on the rear panel of this unit or AUDIO IN (L(MONO)/R)/ VIDEO IN on the front of this unit to the audio out and video out sockets on the TV using the audio and video cables. 2. Insert a video cassette with protection tab into your VCR. The video cassette should have the window side facing up and the arrow facing away from you. Your unit will switch on automatically. You can also switch it on with the POWER button. 3. Select the channel you wish to record with the TV’s channel selector. 4. Press AV until the socket you wish to record from is displayed. AV 1 for recording from AUDIO (L/R)/VIDEO (VCR IN AV1) terminals on the rear of your unit. AV 2 for recording from AUDIO IN (L(MONO)/R)/ VIDEO IN terminals on the front of your unit. 5. Press LP if you wish to record in Long Play or Standard Play. SP will produce improved picture and sound quality, however LP will provide twice as much recording time as SP. SP or LP will be displayed in your VCR display to let you know which you have selected. 6. Press REC/ITR to start recording. RECORD will appear on the TV screen. Press REC/ITR several times. Each successive press will increase the record time by 30 minutes until you reach a maximum of 9 hours. 7. Press PAUSE/STEP to avoid recording unwanted scenes. Press PAUSE/STEP to continue recording. If you press PAUSE/STEP during ITR, this unit will enter the record pause mode and the recording mode will be back to normal recording mode. Tapes can be paused for up to 5 minutes; RECP will be displayed when a tape is paused. After 5 minutes your VCR will stop recording to prevent damaging the tape or your VCR. 7. Press STOP to end recording. Press EJECT. EJECT will appear on the TV screen for a few seconds. If the end of the tape is reached, your VCR will stop recording automatically, rewind, stop, eject the tape. Notes: • If you do not wish to record on a tape (this can happen quite easily by accident!) remove the protection tab on the back edge of the video cassette. • It is possible to record on a video cassette with the record protection tab removed by covering the hole with self adhesive tape. 20 Playing a DVD Playback Setup 1. Turn on the TV and select the video input source connected to the DVD player. 2. Turn on the audio system (if applicable) and select the input source connected to the DVD player. 3. Press OPEN/CLOSE to open the disc tray and load your chosen disc in the tray, with the playback side down. 4. Press OPEN/CLOSE to close the tray. Playback starts automatically. If playback does not start, press N. In some cases, the disc menu might appear instead: DVD Use the bB v Vbuttons to select the title/chapter you want to view, then press ENTER to start. Press TITLE or DISC MENU to return to the menu screen. Notes: • If parental control is set and the disc is not within the rating settings you must input the password. (See “Lock Menu” on page 18.) • DVDs may ha...