Votes - 5, Average rating: 4
(
)
)
|
Other manuals for this model:
manual abstract
If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow. 1. Select [Connection Setting] option in the [Setup] menu then press ENTER ( ). 2. The [Connection Setting] menu appear on the screen. Use U/u to select the [Wired] and press ENTER ( ). 3. Selects [Yes] and press ENTER ( ) to continue. The new connection setting resets the current network settings. 4. Use U/u/I/i to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. NOTE If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set the [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using U/u/I/i and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part. 5. Select [OK] and press ENTER ( ) to apply network settings. 6. The player will ask you to test the network connection. Select [OK] and press ENTER ( ) to complete the network connection. 7. If you select [Test] and press ENTER ( ) at step 6 above, the network connection status is displayed on the screen. You can also test it on the [Connection Status] in the [Setup] menu. HX995TZ-DD.BRUSLL_ENG_0893.indd 32 10. 09. 14 3:24 Installation33 Wireless Network Connection Another connection option is to use an Access Point or a wireless router. In the example configuration for wireless connection below, this player would be able to access content from either of the PCs. The network configuration and connection method may vary depending on the equipment in use and the network environment. Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings. Installation Wireless Network Connection WANWireless Communication Player PC Broadband service Access Point or Wireless Router NOTE 3 • For best performance, a direct wired connection from your Home theatre to your home network’s router or cable/DSL modem is always the best option. If your Home theatre is far away from your router or cable/DSL modem. Ethernet or LAN cables are available at many stores in lengths of 15 m and longer. If you do chose to use the wireless option, note that performance can sometimes be affected by other electronic devices in the home. • An Access Point is a device that allows you to connect to your home network wirelessly. HX995TZ-DD.BRUSLL_ENG_0893.indd 33 10. 09. 14 3:24 34 Installation 3 Installation Wireless Network Setup Before setting the wireless network, you need to: – connect the broadband internet to the wireless home network. – set the access point or wireless router. – note the SSID and security code of the network. For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the [Setup] menu. Adjust the [NETWORK] setting as follow. Setting up the access point or the wireless router is required before connecting the player to the network. 1. Select [Connection Setting] option in the [Setup] menu then press ENTER ( ). 2. The [Connection Setting] menu appear on the screen. Use U/u to select [Wireless] and press ENTER ( ). 3. Selects [Yes] and press ENTER ( ) to continue. The new connection setting resets the current network settings. 4. The player scans the all available access points or wireless routers within range and display them as a list. Use U/u to select an access point or wireless router on the list, and then press ENTER ( ). If you have security on your access point or wireless router, verify that the WEP or WPA key that was entered into the player matches the router’s information exactly. You need to input the security code as necessary. NOTE WEP security mode generally have 4 keys available on an access point or wireless router’s setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network. HX995TZ-DD.BRUSLL_ENG_0893.indd 34 10. 09. 14 3:24 Installation35 [Manual] – Your access point may not be Notes on Network Connection: broadcasting its access point name(SSID). Check your router settings through your computer and either set your router to broadcast SSID, or manually enter the access point name(SSID) in [Manual]. [Push Button] – If your access point or wireless router that supports Push Button Configuration method, select this option and press the Push Button on your access point or wireless router within 120 counts. You do not need to know the access point name (SSID) and security code of your access point or wireless router. 5. Use U/u/I/i to select the IP mode between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically. NOTE If ther...