Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
If necessary, place the device on a nonslip pad. Thunderstorms! Equipment connected to a power supply can be damaged during a thunderstorm. You should therefore always pull the power plug from the power socket when there is a storm. Notice regarding electrical power surges (EFT / electrical fast transient) and electrostatic discharges: In a case of malfunction due to an electrical fast transient (power surge) and/or electrostatic discharge, the device must be returned to default settings in order to re-establish normal operation. Possibly the power supply must be separated and then reconnected. The batteries (if present) must be removed and then reinserted. Notice regarding separation from mains-power The POWER switch does not completely disconnect the device from the power network. Additionally, the device consumes power when in stand- by-mode. To completely separate the device from mains-power, the power plug MUST be removed from the wall socket. Information regarding the handling of batteries The remote control is operated by batteries. For the handling of batteries please observe the following: Risk of explosion! Do not throw batteries into a fire. Do not recharge the batteries. • Never open batteries, never solder or weld batteries. The risk of explosions and injuries exists! • Regularly check the condition of the batteries. Leaking batteries can cause damage to the device. • If you do not intend to use the device for an extended period, remove the batteries. • In the event of the batteries leaking acids, wear protective gloves. • Clean the battery compartment and the battery contacts with a dry cloth. Attention! No liability/warranty will be considered for damage to the DVD player caused by the effects of moisture, water penetration or overheating! 7. Remote control 7.1 Inserting the batteries 1. Open the battery compartment on the rear of the remote control. 2. Place the two supplied batteries type AAA (micro cells) into the battery compartment. Make sure that the batteries are inserted in accordance with the correct polarity. 3. Replace the battery compartment cover. 7.2 Using the remote control In order to guarantee faultless operation when using the remote control… • Always point the remote control, during use, directely at the DVD player • Make sure that there are no obstructions between the remote control and the DVD player that will hinder reception. • When using the remote control place yourself not more than 5 metres from the DVD player otherwise interferences can occur during operation of the DVD player functions with the remote control. 7.3 Replacing the batteries If the operation of the DVD player via the remote control does not function properly or does not function at all the batteries must be replaced • Always renew all batteries in order to return the remote control to its full performance ability. 8. Connecting the DVD Player to a television After setting up the DVD player, you can now connect it to a television. The DVD player can be connected to televisions which operate with the PAL and NTSC standards. If you want to use the DVD player on a television with the NTSC standard you must change the video setting in the DVD players "OSD menu". There PAL is set as the television standard at the factory. On this topic see also chapter 10.3. "Video settings: Setting the TV standard". Depending on the televisions equipment there are different methods of connecting the DVD player to it, these are explained as follows. - 6 8.1 Connecting to a television via ScartCable/RGB 8.3 Connection to a television via video input (Composite Note: Connecting the DVD player to a television with a Scart cable via the RGB input offers a high quality connection. Select this connection variation in the case of televisions equipped with an RGB input. If you are not sure if the television is equipped with an RGB input then you can check this by consulting the television's instruction manual. • Connect the jack inscribed with EURO SCART to a television Scart socket by using the supplied Scart cable. • For playback select the matching channel on your television Check with the television's instruction manual on how you can set the AV channel. • In the OSD menu select the menu Video/Video output/RGB. On this topic see also chapter 10.3 "Video settings: Video output. 8.2 Connecting to a television via S-Video Note: For this type of connection the television must have available an S VIdeo input and two audio "IN" cinch sockets. If you are not sure if the television is equipped with S Video and/or cinch sockets you can check this by consulting the television's instruction manual. For this connection variant you will need: • an audio cinch cable (not supplied) • an S-video cable (not supplied) These can be obtained from your dealer. To connect the DVD player to a television via S-video: • Connect the jack inscribed with S-VIDEO to a television S-video socket using an S-video cable. • Connect the audio output sockets L/R ...
Other models in this manual:DVD Players - KH 6517 (1.13 mb)