You can select “On” or “Off” of the error tone for “Write error”, “Input clip” and “BATT warning”, as well as can set the time for “Disk warning”. 1) While the unit is stopped, press the [SHIFT] key to light the SHIFT indicator, followed by the [ENTER/YES] key. 2) While “SYS SETUP” is highlighted, press the [ENTER/YES] key. The display now shows the SYS SETUP menu screen. 1. A write error happens during recording. [Write error] 2. The peak indicator lights due to input overload during analog recording or clipping of the stereo buss. [Input clip] 3. The battery voltage drops below the threshold voltage set by the "BATT. warning" menu item. [BATT warning] 4. The remaining recording time of a disk (or a partition) gets under the specified time. [Disk warning] Chapter 8: MENU mode/SYS SETUP menu • Input clip On/Off setting Use the [MENU] dial to select the “Input clip” and press the [ENTER/YES] key. The current setting starts flashing and you can now select the desired option. Flashing Use the [MENU] dial to select the desired option and press the [ENTER/YES] key to confirm your setting. Options You can select between “On” and “Off” (the default is “On”). If the peak indicator lights due to input overload during analog recording or clipping of stereo buss while you set "Input clip" to "On", the warning tone is output by the pattern on the right. • BATT warning On /Off setting Use the [MENU] dial to select the “BATT warning” and press the [ENTER/YES] key. The current setting starts flashing and you can now select the desired option. Flashing Use the [MENU] dial to select the desired option and press the [ENTER/YES] key to confirm your setting. Options You can select between “On” and “Off” (the default is “On”). If the battery voltage drops below the threshold voltage set by the "BATT. warning" (BATTERY SETUP) menu item while you set "BATT warning" to "On", the warning tone is output by the pattern on the right. If the warning tone above is output during recording, recording automatically stops after one minute. :For details about how to set the battery threshold voltage for warning, see "Battery warning setting" on page 172. Location Recorder Model PD204 161 Chapter 8: MENU mode/SYS SETUP menu • Disk warning time setting Use the [MENU] dial to select the “Disk warning” and press the [ENTER/YES] key. The current setting starts flashing and you can now select the desired option. Flashing Use the [MENU] dial to select the desired option and press the [ENTER/YES] key to confirm your setting. Options Selectable “Off” or between “1min.” and “9min.” in one minute steps (the default is “3min.”). If the remaining recording time of a disk (or a partition) gets under the specified time while you set "Disk warning" to "On", the warning tone is output by the pattern on the right. 4) Press the [EXIT] key repeatedly until you exit the MENU mode. 162 Location Recorder Model PD204 Chapter 8: MENU mode/SYS SETUP menu Chain play mode setting [Chain play] The “Chain play” menu item selects how the recorder behaves after playback of an audio file finishes. By default, the recorder stops at the playback end point. However, you can make the recorder pause at the beginning of the next audio file or play the next audio file until all audio files on a disk (or a partition) are played back. 1) While the unit is stopped, press the [SHIFT] key to light the SHIFT indicator, followed by the [ENTER/YES] key. 2) While “SYS SETUP” is highlighted, press the [ENTER/YES] key. The display now shows the SYS SETUP menu screen. 3) Use the [MENU] dial to select the “Chain play” menu item and press the [ENTER/YES] key. The current setting starts flashing and you can now select the desired option. Flashing Options You can select from among “Off”, “Pause” and “AutoPly (the default is “Off”). Off The unit stops when an audio file is played back to the end. Pause The unit pauses at the beginning of the next audio file when an audio file is played back to the end. AutoPly The unit continuously plays back all audio files following the current file on the current disk (or partition) in the numerical order. When the unit plays back the last file to the end, it stops. 4) Use the [MENU] dial to select the desired option and press the [ENTER/YES] key to confirm your setting. 5) Press the [EXIT] key repeatedly until you exit the MENU mode. Location Recorder Model PD204 163 Chapter 8: MENU mode/SYS SETUP menu ROM version checking [Version] Selecting “Version” allows you to view the software ROM version number and creation/revision date. 1) While the unit is stopped, press the [SHIFT] key to light the SHIFT indicator, followed by the [ENTER/YES] key. 2) While “SYS SETUP” is highlighted, press the [ENTER/YES] key. The display now shows the SYS SETUP menu screen. 3) Use the [MENU] dial to select the “Version” menu item and press the [ENTER/YES] key. You can check the software ROM version number and creation/revision date. 4) Press the [EXIT] key repeatedly until y...
)
