Votes - 1, Average rating: 4
(
)
)
|
manual abstract
The supplied AV cable is made up of an analog audio cable and a composite video cable. • Push each plug in all the way to make a good connection (loose connections can cause noise or malfunctions). •To prevent interference, keep audio and video cables away from power cords and speaker cables. The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In this setup, stereo audio is played through the speakers in your TV. 1. Connect the VIDEO OUTPUT and AUDIO OUTPUT FRONT/D.MIX 1 jacks to a set of AV inputs on your TV. Use the supplied AV cable (RCA), connecting the red and white plugs to the audio outputs and the yellow plug to the video output. The DVD payer has two composite video output connectors and two pairs of stereo analog audio output connectors. They output the same video and audio signals respectively. See the following page if you want to use other cable for the video connection. 2. Connect the supplied AC power cord to the AC INLET, then plug into a power outlet. Before Making Any Connections Right (red) Left (white) (Yellow) Analog audio Composite video Right (red) Left (white) (Yellow) Right! Wrong! Basic Setup L R ANALOG INPUT VIDEO IN To power outlet TV AV cable (Supplied) Power cord (Supplied) This player is equipped with copy pro- tection technology. Do not connect this player to your TV via a VCR using AV cables, as the picture from this player will not appear properly on your TV. (This player may also not be compati- ble with some combination TV/VCRs for the same reason; refer to the manu- facturer for more information.) DPS-6.7_En.bookPage20Monday,July31,20063:12PM 21 Connecting the DVD player—Continued • Connect the DVD player directly to your TV. If you connect the DVD player through a VCR, TV/VCR combination, or video selector, the picture may be dis- torted because DVD-Video discs are usually copy pro- tected. Using S-Video If your TV (or other equipment) has an S-Video input, you can use this instead of the standard (composite) out- put for a better quality picture. • Use an S-Video cable (not supplied) to connect the S VIDEO 1 or 2 OUTPUT to an S-Video input on your TV (or monitor or AV receiver). The S VIDEO 1 and 2 jacks output the same video signals, so use either. Line up the small triangle above the jack with the same mark on the plug before plugging in. Using Component Video You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). This will provide better quality picture than S-Video. • Use a RCA/phono or BNC component video cable (not supplied) to connect the COMPONENT 1 or 2 VIDEO OUTPUT jacks to a component video input on your TV (or monitor or AV receiver). The COMPO- NENT 1 and 2 jacks output the same video signals, so use either pair. If you connect the component video output to a TV or another component that doesn’t support progressive scanning, be sure to turn off HDMI (see page 43). You can set the component video output to Progressive or Interlaced (see page 43). Compatibility of this unit with progressive-scan TVs. This player is compatible with progressive video Macro Vision System Copy Guard. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOM- MENDED THAT THE USER SWITCH THE CON- NECTION TO THE “STANDARD DEFINITION” OUTPUT. IF THERE ARE QUESTIONS REGARD- ING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. Connecting Your TV (video only) S VIDEO IN S VIDEO TV or COMPONENT1 2 Y Y PB PR COMPONENT VIDEO IN PR PB Y PR PB Y PR PB TV or DPS-6.7_En.bookPage21Monday,July31,20063:12PMConnecting the DVD player—Continued • Connect the DVD player directly to your TV. If you connect the DVD player through a VCR, TV/VCR combination, or video selector, the picture may be dis- torted because DVD-Video discs are usually copy pro- tected. Using S-Video If your TV (or other equipment) has an S-Video input, you can use this instead of the standard (composite) out- put for a better quality picture. • Use an S-Video cable (not supplied) to connect the S VIDEO 1 or 2 OUTPUT to an S-Video input on your TV (or monitor or AV receiver). The S VIDEO 1 and 2 jacks output the same video signals, so use either. Line up the small triangle above the jack with the same mark on the plug before plugging in. Using Component Video You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). This will provide better quality picture than S-Video. • Use a RCA/phono or BNC component video cable (not supplied) to connect the COMPONENT 1 or 2 VIDEO OUTPUT jacks to a component video input on your TV (or monitor or AV receiver). The COMPO- NENT 1 and 2 jacks outp...
Other models in this manual:DVD Players - DPS-6.7 (1.81 mb)
DVD Players - DPS-6.7 (1.81 mb)