Votes - 2, Average rating: 3
(
)
)
|
manual abstract
.4. .5. .6. Clear Step Mute Title Power Menu Enter Direction buttons Mute Numeric buttons Repeat A-B Repeat Audio SubTitle Angle Program PBC Slow Step FF/FB PREV/NEXT Skip Zoom Stop Play/Pause Setup LCD Mode Display Views of the Remote Control Remote Control Battery Installation Connections Connecting to a TV set (TV or monitor with audio/video input) 1. Refer to the owner's manual of your TV as well. 2. Before connecting the DVD player to a TV set, be sure to turn the power off and unplug both units from the wall outlet. Audio/Video cable(Supplied) To AUDIO OUT To VIDEO OUT To AUDIO/VIDEO input Connections .7. .8. Connections Power Connections (to Battery Pack) Basic Playback Function Buttons .9. .10. Function Buttons .11. .12. Function Buttons .13. Setup Menu Setup Menu Item Instruction Default setting .15. .16. Setup Menu Trouble Shooting Should your DVD player develop a problem, please check below before requesting service: Should the player develop a malfunction, unplug the player for 30 minutes. After that, power on the player and the restore function should reset the player. Symptom Check and Action No power 1. Make sure the unit has been powered on manually. 2. Check if the power cord has been properly connected to the power outlet. 3. Make sure the battery pack is fully charged. Does not play 1. No disc, load a disc. 2. Disc has been loaded upside down. Place the disc with the label side up. 3. Disc's rating level is higher than the player's setting. 4. Disc is incorrect type for the player. 5. Disc is damaged or dirty. Clean the disc or try another one. 6. Moisture may be condensed inside the player. Remove the disc and leave the unit power on for one or two hours. No Picture 1. Check if the TV set has been powered on. Use TV remote to select AV signal for DVD rather than broadcast. 2. Check if the system connection is proper and secure. 3. Check if the connection cables are damaged. 4. Clean the disc. Picture noisy/ distorted 1. Disc is damaged or dirty. Clean the disc or try another one. 2. Reset the color system of the TV set. 3. Make sure the DVD player is not connected through a VCR, cable or satellite dish. No sound or sound output not complete 1. Check if the TV and amplifier have been switched on and correctly set. 2. Check if the TV and amplifier system connections are secured. 3. Press AUDIO button to select other audio tracks of the disc. 4. Check if the MUTE function of the TV or amplifier has been activated. 5. There will be no sound output during REVERSE PLAY/PAUSE/SLOW and SEARCH. Remote control does not work 1. Make sure the POWER button on the unit has been turned on manually. 2. Remove the obstacles between the remote control and the player. 3. Point the remote control towards the remote sensor on the player. 4. Check if the batteries of the remote control have been loaded with correct polarities. 5. Replace the batteries of the remote control. Malfunction .17. .18. .19. Specification Video output 1+0.2V (p-p), 75ohm, Negative sync., 3.5 mm mini jack x1 Audio output 1.5 Vrms (1 KHz, 0dB), 3.5 mm mini jack x1 Earphone terminal 3.5mm stereo mini jack x1 Signal /Noise ratio(audio) 90dB typical Dynamic range(audio) 90dB typical Panel size 7 inch (16:9) Resolution 480(H) x 234 (V) (QVGA) Pixels Laser Wavelength 650 nm Operating conditions Temperature: 0 c to 35 c. Operation status : Horizontal Dimensions 187x170x50mm (Main Unit & Batt.) Weight 937g (Main Unit & Batt. ) Power supply DC 9.0V 2A (AC adapter TERMINAL) Power consumption <=9w Signal system NTSC CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Disconnect the apparatus from the mains if it is not in use. Please study this manual carefully and always keep it available. There are, however, some installation and operation precautions which you should be aware of. (1). Read these instructions. (2). Keep these instructions. (3). Heed all warnings. (4). Follow all instructions. (5). Do not use this apparatus near water. (6). Clean only with dry cloth. (7). Do not block any ventilation openings-Maintain well ventilated conditions around the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer's instructions. (8). Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. (9). Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. (10). Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit fr...