Ending/ cancelling oven cleaning Turn the operating mode and temperature selector back to the U position. Removing and fitting the appliance door You can remove the appliance door to clean it more thoroughly. : Risk of injury! The hinges of the appliance door may snap shut with great force. Always open the hinge locking lever fully when removing the appliance door and close it fully after refitting. Do not reach into the hinge. : Risk of injury! If the appliance door has only been unhinged on one side, do not reach into the hinge. The hinge can snap back with great force. Call the aftersales service. Removing the appliance door 1. Open the appliance door fully. 2. Open the locking levers on the left and right- hand side fully. The hinges are secured and cannot snap closed. 3. Close the appliance door until resistance becomes noticeable ( figure A) 4. With both hands, grip the door on the left and right- hand side, close the door a little more and pull it out (figure B) . Fitting the appliance door 1. Insert the hinges in the left and right- hand holders (figure C). The notch on both hinges must engage. 2. Open the appliance door fully. 3. Close the locking levers on the left and right-hand side fully (figure D). . . The appliance door is secured and can no longer be removed. 4. Close the appliance door. Cleaning the door panels To facilitate cleaning, you can remove the inner door panels from the appliance door. : Risk of injury! The components inside the appliance door may have sharp edges. Take care not to cut yourself. Wear protective gloves. : Risk of injury! The appliance must not be used again until the door panels and appliance door have been correctly fitted. Removing the door panel Note: Before removing, make a note of which way round the door panel is fitted, so that it is not refitted the wrong way round. 1. Unhook the appliance door and lay it on a soft, clean surface with the front side facing downwards ( see section: Removing and installing the appliance door). 2. Pull off the cover at the top of the appliance door. Press in the tabs on the left and right using your fingers ( fig.A) . 3. Lift the door panel slightly and pull it out (Fig. B). . . Removing the intermediate panel Lift the intermediate panel slightly and pull it out towards you. Cleaning Clean the door panel with glass cleaner and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, or sharp or abrasive cleaning aids or detergents. Fitting the intermediate panel Note: During installation, make sure that the lettering " top right" is upside down at the bottom left. Insert the intermediate panel towards the back as far as it will go. Fitting the door panel 1. Insert the door panel at an angle towards the back into both brackets as far as it will go. The smooth surface must face outwards. 1. Push the hook-in rack upwards at the front and unhook to the side ( figure A) . 2. Pull the hook-in rack forwards at the rear and unhook to the side ( figure B) . 3. Clean the hook-in rack with washing- up liquid and a sponge or brush. 4. Align the hook-in rack with the indentation ( a) facing downwards, so that the shelf heights match. 5. Insert the hook- in rack at the rear as far as it will go and push to the rear ( figure C) . 6. Insert the hook-in rack at the front as far as it will go and push downwards (figure D). 2. Put the cover back in place and press on it until it clicks in place. 3. Refit the appliance door. Cleaning the hook-in racks You can remove the hook-in racks for easier cleaning. : Risk of burning due to hot components in the cooking compartment! Wait until the cooking compartment has cooled down. Faults and repairs It is not always necessary to call the after-sales service. : Risk of electric shock! Sometimes, you can find a remedy yourself. You will find some ¦ Work on the appliance electronics may only be performed by tips for troubleshooting in the following table. a specialist. ¦ Always disconnect the appliance from the power supply when work is carried out on the electronics. Switch off the circuit breaker or remove the fuse from your household fuse box. Problem Possible cause Remedial action Electrical function is faulty ( e. g. indicator Circuit-breaker faulty Check circuit-breakers in the fuse box and lamps do not light up) replace if necessary Liquid or thin dough runs to one side Appliance not installed level Check the appliance installation ( see the Installation instructions) ‹ : ‹‹ flashes in the clock display There was a power cut Reset the clock (see section: Electronic clock) Electronically controlled functions are mal- Energy surges (e. g. lightning strike) Reset the function concerned functioning Problem Possible cause Remedial action Smoke is generated during roasting or grill- Fat is burning on the grill element Continue grilling or roasting until the fat on ing the grill element is burnt away Wire rack or universal pan inserted inc...

Other models in this manual:
Ovens - B15M52N3GB/04 (1.45 mb)
Ovens - B15M52S3GB/01 (1.45 mb)
Ovens - B15M52S3GB/04 (1.45 mb)