Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Children must be supervised in the proximity of any air tool or work area. 17) Follow air supply manufacturer’s recommendation for connection of regulators, filters and other accessories. Do not install quick couplers directly on air tool, it puts unnecessary strain on the air inlet threads, instead install a short length of air hose to the tool. Do not over tighten fitting connecting to the air tool; this could cause the housing to crack. Use Teflon tape or pipe sealant carefully to prevent excess from entering the air tool. Wear hearing protection. Wear eye protection. Read the instruction manual Wear respiratory protection. BEFORE USING THIS AIR TOOL To ensure long life be sure to oil the tool daily. Pour 4 drops of Eagle air tool (SEA 20 non detergent) oil into the air inlet, and then run the tool for a few seconds to clean. If tool is an impact wrench fitted with a “Zirc” grease fitting: The hammer mechanism of this tool also needs to be greased from time to time (depending on usage). The tool is equipped with grease fitting for this purpose; use this connection to re-grease the tool using Eagle impact wrench grease. PLEASE USE EAGLE SEA 20 NON DETERGENT OIL OPERATING INSTRUCTIONS This ratchet is designed to speed up productivity, not for high torque applications such as head bolts, lug nuts, etc. DO NOT USE THIS RATCHET UNDER POWER TO BREAK FASTENERS LOOSE. Loosen fasteners by hand without depressing throttle. Once loose depress throttle. Always perform final torque tightening by hand. This ratchet is rated to 3/8” bolt size. Rating will decrease for U-bolts, long cap screws, spring fasteners and rusted or corroded fasteners. All these factors absorb power and reduce torque capability. Use the simplest socket to wrench hook-up. Any additional extensions, U-joints or adapters will absorb power and reduce torque capability. Forward/Reverse Lever - Select “F” for forward (clockwise) or “R” for reverse (counter clockwise) operation. Do not attempt to change direction while tool is running. If fastener bogs, slows or binds the tool (or, if the fastener fails to move in 5 seconds), use a large size impact wrench with a higher torque rating. Overloading this tool will cause premature wear and/or permanent damage to internal and external drive parts and will void warranty. TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Air tool does not run or runs slow. Lack of lubrication. Lubricate as per instructions. Dirt in tool. Clean with mixture of 50/50 tool oil/solvent. Lubricate after cleaning. Insufficient air pressure. Check regulator and air supply for leaks. Check compressor to make sure it operates at correct pressure. Make sure air hose is properly sized and that multiple hoses are not connected to same outlet. Check air hose for leaks and repair. Rotor blades worn or motor bearing worn or dirty. Replace blades, inspect clean or replace bearing. IMPACT WRENCH does not impact or impacts slowly. See causes (above). See remedies (above). Broken or worn impact mechanism. Inspect and repair as required. Wear hearing protection. Wear eye protection. Read the instruction manual Wear respiratory protection. Wear hearing protection. Wear eye protection. Wear respiratory protection. Read the instruction manual PARTS BREAKDOWN INDEX PART DESCRIPTION QTY 1 75001 Housing 1 2 75002 Valve Stem 1 3 75003 Throttle Lever 1 4 75004 O-Ring 1 5 75005 Trigger Pin 1 6 75006 Air Inlet 1 7 86021 Spring 1 8 86022 Lock Pin 1 9 16012 O-Ring 1 10 75010 Air Regulator 1 11 15043 Steel Ball 1 12 75012 O-Ring 2 13 15041 Steel Ball 1 14 75014 Inlet Adaptor 1 15 75015 Valve Spring 1 16 75016 Throttle Valve 1 17 75017 Valve Seat 1 18 75018 Plastic Grip 1 19 75019 O-Ring 1 20 75020 Exhaust Deflector 1 21 15040 Spring 2 22 150 0 Ball Bearing 4 2 15029 Rear End Plate 1 24 150 1 Dowel Pin 1 25 15026 Rotor Blade 4 26 15025 Rotor 1 27 1524 Cylinder 1 28 15027 Front End Plate 1 29 15028 Ball Bearing 1 0 4501 Washer 1 1 15012 Thread Ring Gear 1 2 15014 Plate Gear 15014 Gear Pin 4 15015 Gear Plate 1 5 15016 Clamp Nut 1 6 1501 -01 Bushing 1 7 15020 Needle Bearing 1 8 15021 Crank Shaft 1 9 45019 Ratchet Housing 1 40 45021 Drive Bushing 1 41 45024 Ratchet Yoke 1 42 1502 -01 Reverse Button 1 4 450 8-01 Spring 2 44 150 4 Lock Pin 2 45 450 4 Washer 1 46 45052 Anvil 1 47 45020 Pin 2 48 450 7 Ratchet Pawl 2 49 450 8 Thrust Washer 1 50 150 9 Retainer Ring 1 51 15044 Spring 1 Bolt Capacity ................................................................................................................................................................ /8” Max torque (FT/LBS)......................................................................................................................................................60 Air pressure (PSI) (Tool in use at full throttle).................................................................................................................90 Average air consumption (CFM)................................................................