Votes - 3, Average rating: 4
(
)
)
|
manual abstract
(3) Move charger and tool to a surrounding air temperature of 40°F (4,5 °C) to 105°F (+40,5 °C). (4) If the charger is mounted on a wall make sure the charge indicator light is on. If the indicator light is not on, push unit down to make sure charging contacts are touching. (5) If the receptacle and temperature are OK, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in a depleted condition. 6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although extended charging is not a safety concern, it can significantly reduce overall battery life. Attaching Screwdriver Bit Tips Holder (Figure 1) Attach the holder (K) to either side of the charging cradle (F) ( using the screw provided) as shown in figure 1. Wall Mounting (Figures 2, 3 & 4) Use the hardware provided only if hanging on conventional sheet rock or plaster walls. If not hanging on conventional sheet rock or plaster walls, please use the appropriate fasteners for that material. 1. Attach the wall mount tool support (J) as shown in figure 2. CAUTION: The tool support must be securely attached to the charging cradle when it is mounted on a vertical surface. 2. Choose a location that is within reach of an electrical outlet. Fix the charging cradle (F) as shown in figure 3 and 4. NOTE: Avoid damaging the cord while fixing the charging cradle to the wall. 3. Plug in and place the product in position. Make sure the charge indicator light is on. If the indicator light is not on, push unit down to make sure charging contacts are touching. Operating Instructions Inserting an Accessory (Figure 5) The LI3000 compact screwdriver is designed for use with screwdriver bits. Do not use double ended screwdriver bits. To install a bit simply insert it into the cavity in the hex spindle as shown in figure 5. To remove the bit pull it straight out. Switch (Figure 6) To turn the tool ON in a forward direction, push the switch to the forward position(6A), squeeze the trigger and the tool will run. Release pressure from the trigger and the tool will stop. To turn the tool ON in a reverse direction, push the switch to the rearward position(6B), squeeze the trigger and the tool will run. Release pressure from the trigger and the tool will stop. With the switch in the middle position, the trigger will not be active and the spindle will be locked (6C). Use the tool in this mode as any conventional non-powered screwdriver. Maintenance Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. Troubleshooting Problem Possible Cause Possible Solution • Unit will not start. • Battery not charged. • Check battery charging requirements. • Battery will not charge. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Check current at receptacle by plugging in a lamp or other appliance. • Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. • Surrounding air • Move charger and tool to a temperature too hot or surrounding air temperature of too cold. above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. Lubrication Black & Decker tools are properly lubricated at the factory and are ready for use. Accessories Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO. (800-544-6986) CAUTION: The use of any accessory or attachment not recommended may be hazardous. The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium-ion battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative. RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent lithium-ion batteries. Help protect our env...