Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
England. Tel: (++44) 0114 221 2500 Fax: (++44) 0114 221 2560 Email: info@rotabraoch.co.uk Web: A MEMBER OF THE OSL GROUP OF COMPANIES This machine (Serial No ) is CE approved. RLL233 RLL233 Issue 4 Aug 2007 1 CONTENTS OF THE MANUAL. Page [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] Specification of machine. General procedures and safety measures. Operating instructions. Extension cable selection. Mounting of cutters. Cutters and pilots. Remedies for hole making problems. Wiring diagram. Exploded view and component parts of complete machines. Exploded view and component parts of gearbox and motor units. Pipe adapter kit. Wiring of mains plug. Cutting Speeds. Cable replacement. 2 3 4 5 5 6 7 9 11 12 14 15 16 18 List of Contents with Magnetic Drill Unit Check List RD4329 Safety Strap YES/NO RA356 Pilot YES/NO RA359 Pilot YES/NO RA3013 Pilot YES/NO RA3030 Pilot YES/NO RA3047 Pilot YES/NO RA3057 Pilot YES/NO RD4088 4mm A/F Tee Handled Hexagon Key YES/NO RD4152 3mm Hexagon Key YES/NO RLL233 Issue 4 Aug 2007 2 [1] ROTABROACH MAGNETIC DRILLING MACHINE MODELS CM/200/1/ & CM/200/3 Maximum hole cutting capacity in .2/.3C steel = 65mm dia. x 50mm deep Arbor bore = 19.05mm (3/4") dia. Motor Unit Voltages 110v 230v normal full load 14 A 1400 W 6 A 1400 W Electro Magnet 0.6A 69W 0.3A 69W Size 180mm long 90mm wide Tractive Force at 20°C with 25mm minimum plate thickness The use on any material less than 25mm thick will progressively reduce the magnetic performance. If possible, substitute material should be positioned under the magnet and work piece to equate to a suitable material thickness. If this is not possible, an alternative secure method of restraining the machine MUST be used. 1200kgs Total Load (magnet + motor) 1469 W 1469 W Overall Dimensions Height - maximum extended 550mm Height - minimum 470mm Width (including Hand wheel) 200mm Length Overall (including Guard) 270mm Nett Weight 16kgs Maximum hand/arm vibration magnitude (measured at handle during operation in accordance with ISO5349, using a 22mm cutter through 13mm MS plate) 0.82 m/s_ Estimate of likely daily vibration exposure. Operation 30 holes @ 2 minute/hole. 0.29m/s_ A(8) Average noise level during cutting at operators ear position. 89dB(A) Ear defenders must be worn when operating this machine These tools are UK designed, and manufactured with globally sourced components and conform with the requirements of EEC Document HD.400.1 and BS.2769/84 Suitable only for a single phase 25-60Hz A.C. power supply DO NOT USE ON D.C. SUPPLY Do not use your magnetic drill on the same structure when arc welding is in progress. D.C. current will earth back through the magnet and cause irreparable damage. WARNING: THIS APPLIANCE MUST BE EARTHED! NB: ANY MODIFICATIONS TO THIS MACHINE WILL INVALIDATE THE GUARANTEE RLL233 Issue 4 Aug 2007 3 READ BEFORE USING THE MACHINE [2] SAFETY PROCEDURES • When using electrical tools, basic safety precautions should always be followed to reduce the risk of electric shock, fire, and personal injury. • Do NOT use in wet or damp conditions. Failure to do so may result in personal injury. • Do NOT use in the presence of flammable liquids or gases. Failure to do so may result in personal injury. • ALWAYS SECURE THE MACHINE WITH THE SAFETY STRAP - PART NO. RD4329 BEFORE STARTING TO OPERATE - for the user's protection in case of power failure or the magnet's breaking loose whilst in use. Failure to do so may result in personal injury. • ALWAYS WEAR APPROVED EYE AND EAR PROTRCTION WHEN THE EQUIPMENT IS IN OPERATION. Failure to do so may result in personal injury. • Disconnect from the power source when changing cutters or working on the machine. • When changing cutters, or removing swarf, ALWAYS wear approved gloves. • ALWAYS ENSURE CUTTER RETAINING SCREWS ARE SECURE - they sometimes vibrate loose when the machine is in continuous use. • Regularly clear the work area and machine of swarf and dirt, paying particular attention to the underside of the magnet base. • With a gloved hand, and after switching off, remove any swarf which might have gathered around the cutter and arbor before proceeding with the next hol...
Other models in this manual:Power Screwdrivers and Drills - MAGNETIC CM/200/1 (1.18 mb)
Power Screwdrivers and Drills - MAGNETIC CM/200/3 (1.18 mb)
Power Screwdrivers and Drills - MAGNETIC CM/200/1 (1.18 mb)
Power Screwdrivers and Drills - MAGNETIC CM/200/3 (1.18 mb)