Votes - 3, Average rating: 4.7 ( )

Manafacture: Global Machinery Company File size: 322.19 kb File name: Language of manual:

Do not allow any liquid to come into contact with the charger. There is a danger of electric shock. • To allow the battery pack to cool down after charging, do not place it in a hot environment such as a metal shed or open trailer left in the sun. • The charger is not intended for any use other than charging the exact type of rechargeable battery pack as supplied with the charger.Any other use may result in the risk of fire, electric shock or electrocution. • The charger and battery packs supplied with it are specifically designed to work together. Do not attempt to charge the battery pack with any other charger than the one supplied. • Do not place any object on top of the charger as it could cause overheating. Do not place the charger near any heat source. • Do not pull on the lead of the charger to disconnect it from the power source. • Make sure that the charger cable is positioned where it will not be stepped on, tripped over or otherwise subjected to damage or stress. • Do not use an extension cord unless it is absolutely necessary. The use of an improper extension cord could cause the risk of fire, electric shock or electrocution. • Do not use the charger if it has been subjected to a heavy knock, dropped or otherwise damaged in any way. Take the charger to an authorised service centre for a check or repair. • Do not disassemble the charger. Take it to an authorised service centre when service or repair is required. Incorrect re-assembly may result in the risk of fire, electric shock or electrocution. • To reduce the risk of an electric shock, unplug the charger from the power supply before attempting to clean it. Removing the battery alone does not reduce the risk. • Never attempt to connect two chargers together. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104°F (40°C) such as alongside sheds or metal structures in the summer. • The charger is designed for use from a standard household electrical supply (230–240 volts). Do not attempt to connect the charger to a supply with a different supply. • If you wish to charge a second battery pack, unplug the charger from the mains supply and leave it for at least 15 minutes. After this time you can charge a second battery pack. Additional safety instructions for the battery pack • The battery pack for this tool has been shipped in a low charge condition.You should charge the battery pack fully before use. • To ensure the longest battery life and best battery performance, always charge the battery when the air temperature is between 18–24°C. Do not charge the battery pack when the temperature is below 0°C, or above 40°C. This is important. Failure to observe this safety rule could cause serious damage to the battery pack. • Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire. • Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • The battery pack utilizes nickel-cadmium cells. Cadmium is considered to be a toxic material. Use an environmentally safe disposal unit at a municipal waste disposal centre to dispose of a damaged or worn out battery. Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Fitting and removing the battery pack To remove the battery pack from the drill firmly press the battery release tabs (7) at either side of the battery pack, and slide the battery backward out of the tool. To install the battery pack, align rails, on the tool with the tabs on the battery pack and slide the battery pack on to the drill. Ensure the battery pack is sitting straight on the foot and correctly entering the runners. The battery should slide fully on to the drill foot until the battery pack “clicks” into position. Battery charging Important. Before plugging in the power supply from the charger to the slim line adaptor always ensure that the plug is switched off at the mains. Important. The battery will be fully charged after 3-5 hours, remove it from the charger after this time. Do not leave a battery charging for longer than 24 hours. 1. Align and slide the slim line adaptor (9) onto the battery until the battery pack latches “click” into position. Check the adaptor is flush with the battery and there is a firm connection. 2. Connect the power supply from the charger to the slim line adaptor via the socket in the rear of the adaptor housing. 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4. The battery charging time is approximately 3–5 hours. The red LED goes out...

Download now

Please, enter two numbers from picture: