Votes - 4, Average rating: 4 ( )

Manafacture: Draper File size: 336.58 kb File name: 63122ins.pdf Language of manual:

19. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials above or near the tool, so that it is necessary to stand on the tool to reach them. 20. CHECK DAMAGED PARTS Check for damage to parts, breakage of parts, mountings and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. 21. KEEP GUARDS IN PLACE And in working order. 22. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories. All extension cables must be checked at regular intervals and replaced if damaged. Always keep the hand grips on the tool clean, dry and free of oil and grease. 23. USE RECOMMENDED ACCESSORIES Consult the owners manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards. 24. REMOVE ADJUSTING KEYS AND WRENCHES Form a habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. 25. SECURE WORK Use clamps or a vice to hold work.This frees both hands to operate the tool. 26. DO NOT OVERREACH Keep proper footing and balance at all times. 27. USE RIGHT TOOL Do not force the tool or attachment to do a job for which it was not designed. 28. DO NOT FORCE TOOL It will do the job better and safer at the rate for which it was designed. 29. DIRECTION OF FEED Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 30. WHEN DRILLING OR SCREWING INTO WALLS Always make sure there is no danger of hitting any hidden power cables, water or gas pipes in the wall. IMPORTANT NOTE Residual Risk. Although the safety instructions and operating manuals for our tools contain extensive instructions on safe working with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms. Power tools must therefore always be operated with caution ! - 4 ADDED SAFETY INSTRUCTIONS FOR CORDLESS POWER TOOLS Safety is a combination of operator common sense and alertness at all times when the drill is being used. WARNING For your own safety do not attempt to use your drill until the battery is fully charged. Remember the drill is always in an operating condition as it does not need to be connected to a power supply.When not in use place the direction of rotation switch in the neutral position. Before drilling check that there are no hidden hazards such as electrical cables, water or gas pipes running below the surface - use a metal/voltage detector. Do not expose either the drill or charger to rain or water. Do not overcharge the battery (more than 6 hours) as this could damage the battery cells. HEALTH AND SAFETY FOR BATTERIES General: Do not put in fire or mutilate - cells may burst or release toxic materials. Do not short circuit cells, may cause burns. DISPOSAL Do not mutilate batteries, corrosive electrolyte will be released. Do not incinerate - danger of explosion and release of toxic fumes. Do not dispose of batteries or cells in a charged condition. Expired nickel-cadmium batteries must be recycled/disposed of in accordance with the appropriate regulations or legislation. They should be returned to your local warranty agent/stockist. DRAPER HELPLINE: (023) 8049 4344 - 5 UNPACKING AND CHECKING CONTENTS WARNING: For your own safety, never connect the plug to the power supply until all the assembly steps have been completed and you have read and understood the safety and operating instructions. FIG.A .... Cordless hammer drill. .... Battery charger complete with BS approved moulded plug and cable. .... Battery pack. .... Carrying case. .... .... ........ FIG.A Carefully unpack the storage case and its contents from the carton. Place the storage box on a flat level surface. Now open the lid by releasing the two catches which are located at the front of the case. Referring to Fig.A. carefully check that all the parts are present. If any parts are missing or damaged please contact the stockist where your purchase was made or call the Draper Helpline on (023) 8049 4344. - 6 GETTING TO KNOW YOUR CORDLESS DRILL/CHARGER FIG.B .... .... .... .... .... .... .... .... .... .... .... .... TRIGGER -When the variable speed switch trigger is depressed the chuck will rotate (providing the direction switch is in a clockwise or anticlockwise position). .... FORWARD/REVERSE LEVER - This lever determines the direction of rotation of the chuck, i.e. clockwise or anticlockwise. .... KEYLESS CHUCK -This is for holding tools, i.e. drill bits or screwdriver bits. .... RATING PLATE - Shows Part No., voltage, capacity, etc. .... TWO-SPEED GEARBOX SELECTOR SWITCH -This adjusts the rotation speed range of the chuck via the two-speed gearbox. (NOTE: Only change gear when the drill has completely stopped). .... BATTER...

Download now

Please, enter two numbers from picture: