Votes - 2, Average rating: 4 ( )

Manafacture: Makita File size: 891.44 kb File name: 366.pdf Language of manual:

Drilling operation First, slide the action mode change lever to the position of fsymbol. • Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. • Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. CAUTION: • Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. • There is a tremendous force exerted on the tool/bit at the time of hole break through. Hold the tool firmly and exert care when the bit begins to break through the workpiece. • A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. • Always secure small workpieces in a vise or similar hold-down device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Installing set plate (optional accessory) Always install the set plate when using battery cartridges 9100, 9102, 9102A for 6207D or 1200, 1202, 1202A for 6217D/6317D. Install the set plate on the tool with the screw provided. (Fig. 11) MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. (Fig. 12) Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. (Fig. 13) To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centres, always using Makita replacement parts. FRANCAIS Descriptif 1 Batterie 9 Levier de changement 16 Bague 2 Bouton de vitesse 17 Foret 3 Temoin de charge 10 Levier de changement de mode 18 Porte-foret 4 Chargeur 11 Bouton de verrouillage 19 Vis 5 Gachette 12 Bague de reglage 20 Plaque de fixation 6 Inverseur Manchon 13 Graduations 21 Repere d’usure 7 Vers la droite 14 Pointeur 22 Bouchon du porte-charbon 8 Vers la gauche 15 Manchon 23 Tournevis SPECIFICATIONS Modele 6207D 6217D 6317D 6337D 6347D Capacites Acier ......................................10 mm 10 mm 13 mm 13 mm 13 mm Bois .......................................25,4 mm 25,4 mm 25,4mm 32 mm 38 mm Vis en bois .............................6 x 75 mm 6 x 75 mm 6 x 75 mm 6 x 75 mm 10 x 89 mm Vis a metaux ..........................13 mm 13 mm 13 mm 13 mm 13 mm Vitesse a vide (min-1) Grande vitesse ......................0 – 1,300 0 – 1,300 0 – 1,300 0 – 1,300 0 – 1,300 Vitesse reduite .......................0 – 400 0 – 400 0 – 400 0 – 400 0 – 400 Longueur totale ........................233 mm 233 mm 243 mm 243 mm 243 mm Poids net ..................................1,7 kg 1,9 kg 2,0 kg 2,1 kg 2,4 kg Tension nominale .....................9,6 VCC 12 VCC 12 VCC 14,4 VCC 18 VCC • Etant donne l’evolution constante de notre programme de recherche et de developpement, les specifications contenues dans ce manuel sont sujettes a modification sans preavis. • Note : Les specifications peuvent varier suivant les pays. Utilisations L'outil est utilise pour le percage et le vissage dans le bois, le metal et le plastique. Consignes de securite Pour votre propre securite, reportez-vous aux consignes de securite qui accompagnent l’outil. PRECAUTIONS TRES IMPORTANTES POUR LE CHARGEUR ET LA BATTERIE 1. SUIVEZ CES INSTRUCTIONS — Ce manuel contient d’importantes instructions relatives a la securite et au fonctionnement du chargeur. 2. Avant de vous servir du chargeur, lisez toutes les instructions et precautions relatives (1) au chargeur, (2) a la batterie, et (3) a l’outil utilisant la batterie. 3. ATTENTION — Pour eliminer tout risque, ne chargez que des batteries rechargeables MAKITA. Tout autre type d’accumulateur peut eclater, causant dommages ou blessures. 4. N’exposez pas le chargeur a la pluie ou a la neige. 5. L’utilisation d’un accessoire ni agree ni vendu par le fabricant du chargeur peut entrainer un risque d’incendie, de decharge electrique ou de blessure. 6. Pour ne pas risquer d’endommager le cable ou la prise, debranchez en tenant la prise plutot que le cable. 7. Assurez-vous que la position du c...

Download now

Please, enter two numbers from picture: