Votes - 1, Average rating: 3 ( )

Manafacture: Makita File size: 755.98 kb File name: 6831.pdf Language of manual:

Approx. 5 mm (3/16")c Drive a trial screw. If the screw head projects above the surface of the workpiece, turn the adjusting knob in the Wdirection; if the screw head is countersunk, turn the adjust- ing knob in the Bdirection. Casing Stopper plate Adjusting knob Installing the screw strip Insert the screw strip through the screw guide. Then insert it through the feeder box until the first screw reaches the position next to the driving position. Screw guide peder box Driving position Removing the screw strip To remove the screw strip, just pull it out in the direction of the arrow. Carry hook The carry hook is convenient for temporarily hanging the tool. It can be installed on either left or right side of the tool. Hook Switching ON and OFF CAUTl ON: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To switch on, press the trigger. Switch trigger To switch off, release the trigger. \ Driving operation Switch on the tool by pressing the trigger. Hold the tool squarely against the workpiece and apply forward pressure to the tool. The screw will be automatically carried to the driving position and driven into the workpiece. CAUTION: Do not fire the tool without screws. This will damage the workpiece. If the feeder box becomes sluggish in operation, spray car wax (spray type wax) on its sliding surfaces. Never lubricate it. Installing or removing the bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Loosen the bolt which secures the casing. Pull out the casing in the direction of the arrow. Press the dust cover toward the plane bearing and pull out the bit. If the dust cover cannot be moved as far as the plane bearing, try it again after turning the bit slightly. To install the bit, insert it into the socket while turning it slightly. After installing, always make sure that the bit is securely held in place by trying to pull it out. Plane bearing Dust cover 7asing I Hex wrench Screwdriving performance The following reference table indicates the approximate screwdriving capacities from a single charge. It may differ under some condition. 1 Application Thickness of drywall Foundation for drywall Fastenings Battery 1200 Battery 1201 Drywall screw 15/32" x 1") 4.0 mm x 25 mm 12 mm (1 5/32") Steel stud thick 0.5 mm (1/64") Approx. 430 screws Approx. 610 screws Drywall screw 4.0 mm x 40 mm (5/32" x 1-9/16") 18 mm (23/32") Wood or plywood Approx. 230 screws Approx. 330 screws CAUTIO N : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTl ON: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replace- ment parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Fast charger Power display battery (High cap.) 1201A Model DC1201 Part No. 192407-5 Part No. 1 131 26-0 QI Battery cartridge 1200 Hex wrench 3 Part No. 192271-4 Part No. 783201-2 High capacity battery 1201 Part No. 192296-8 Battery cover Phillips bit 2 -117 Part No. 824421-0 Part No. A-1 2697 - Plastic carrying case Hook Part No. 824421-0 Part No. 344056-6 Apr -12-'95 US CORDLESS AUTO FEED SCREWDRIVER Model 6831D Note: The switch and other part configurations may differ from country to country. MODEL 6831D Apr.-12-'95 US ';,'d" DESCRIPTION 'i\M $FD DESCRIPTION 1 1 Name Plate 2 1 Housing Set (With Item 481 3 1 Switch Lever 4 1 Compression Spring 4 5 1 Swntch 6 1 Set Plate ? 1 Battery Holder 8 1 casmg 9 1 Shifter Pin 10 1 Dm1 Cover 11 1 Compression Spring 21 12 1 Phillips Bit 2 -1 17 13 1 Feeder Box 14 1 Pin3 15 1 Stopper 16 1 Leaf Spring 17 1 nox cover 18 1 stopper Plate 19 2 Hex Socket Head Bolt M4x8 20 2 Hex Socket Head Bolt M4x8 21 1 Pan Head Screw M4x18 IWiIh Washerl 22 1 Flat Head Screw M3x5 23 1 Sleeve 4 24 1 Leaf spmg 25 1 Ratchet Disc 26 1 Ratchet Wheel 27 1 Plate 28 1 Plane Beamg 14 29 1 Steel Ball 3 5 30 1 Spindle 31 1 Compression Spring 22 32 1 Helical Gear 55 33 3 PI" 4 34 1 Thrust Needle Bearing 821 35 1 Plane Bearing 8 36 1 Hex Socket Head Bolt M4x25 IWith Washer) 37 1 Knob 40 38 1 Compression Spring 12 39 1 Flat Washer 6 40 1 Countersunk Head Screw M4x12 41 1 Rubber Sleeve 10 42 1 Plane Bearing 5 43 1 Gear Complete 16-49 44 1 Flat Washer 5 45 1 Plane Bearing 5 46 1 Rubber Sleeve 10 47 1 DC Motor 12 V 48 1 Housing Set [With Item 21 ...

Download now

Please, enter two numbers from picture: