Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
9. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it. 4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months. FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 2 1 004908 1. Button 2. Battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Switch action 004909 1 1. Switch trigger CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Electric brake This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after switch trigger release, have tool serviced at a Makita service center. 4 Lighting up the front lamp Lighting up the front lamp 1 1. Lamp CAUTION: • Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action 004911 1 1 A B 1. Reversing switch lever ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit or socket bit 001266 12 mm (15/32”) 9 mm (3/8”) Use only the driver bit or socket bit shown in the figure. Do not use any other driver bit or socket bit. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. 001267 1 2 1. Bit 2. Sleeve This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position. To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. NOTE: • If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Hook The hook is convenient for temporarily hanging the tool. This can be removed without using a tool. This can be installed on either side of the tool. 005954 5 Installing and removing hook Installing and removing hook 005945 A) Removal Remove the battery cartridge from the tool. Place the tool in a stable and level surface. Expand an far end of the hook outward and slide it down while expanding. 005955 B) Installation Remove the battery cartridge from the tool. Place the tool in a stable and level surface. Hold both hooking ends in the upper position and expand the upper part of the hook. 005946 1 1. Hooking ends Expand the other far end in the same manner. 005956 Insert both ends, one by one, of the hook into the grooves in the tool housing. 005947 Keeping the hook in this position, rotate down to the 1 1. Groove in the angle 90°and remove it by pulling in the direction of arrow housing as shown in the figure. 005977 005948 005944 6 Keeping the hook in this position, rotate it upwards to the angle 90°and push both ends fully in the direction of arrow ...