Votes - 3, Average rating: 4
(
)
)
|
manual abstract
002305 Installing or removing battery cartridge • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while sliding the button on the side of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the 1 2 3 1. Red part 2. Button 3. Battery cartridge 1 2 3 4 1. Terminal cover 2. Battery cartridge 3. Charging light 4. Battery charger upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. 001336 Charging 1. Plug the battery charger into the proper AC voltage source. Two charging lights will flash in green color repeatedly. 2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger can be opened with inserting and closed with pulling out the battery cartridge. 3. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will keep lighting up lit steadily during charging. One red charging light indicates charged condition in 0 - 80% and two red ones indicates 80 - 100%. 4. With finish of charge, the charging lights will change from two red ones to two green ones. 5. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its “trickle charge (maintenance charge)” mode which will last approximately 24 hours. 6. After charging, unplug the charger from the power source. NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge from a just operated tool or battery cartridge which has been left in a location exposed to direct sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge is cooled by the cooling fan installed in the charger. When the temperature on battery is more than approx. 70°C, two charging lights may flash in red color, and when approx. 50°C - 70°C, one charging light in red color. • If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. Cooling system • This charger is equipped with cooling fan for heated battery in order to enable the battery to prove its own performance. Sound of cooling air comes out during cooling, which means no trouble on the charger. • Yellow light will flash for warning in the following cases. - Trouble on cooling fan - Incomplete cool down of battery, such as, being clogged with dust The battery can be charged in spite of the yellow warning light. But the charging time will be longer than usual in this case. Check the sound of cooling fan, vent on the charger and battery, which can be sometime clogged with dust. • The cooling system is in order although no sound of cooling fan comes out, if the yellow warning light will not flash. • Always keep clean the vent on charger and battery for cooling. • The products should be sent to repair or maintenance, if the yellow warning light will frequently flash. Conditioning charge Conditioning charge can extend the life of battery by automatically searching the optimum charging condition for the batteries in every situations. The battery employed in the following conditions repeatedly, will be worn out shortly, and yellow warning light may flash. 1. Recharge of battery with its high temperature 2. Recharge of battery with its low temperature 3. Recharge of full charged battery 4. Over-discharge of battery (continue to discharge battery in spite of down of power.) The charging time of such battery is longer than usual. Trickle charge (Maintenance charge) If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will switch into its “trickle charge (maintenance charge)” mode and keep the battery cartridge fresh and fully charged. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop to...