Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Keep your invoice with this manual. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONSFailure to follow all instructions listed below may result in serious injury. SAVE THESE INSTRUCTIONS Keep your work area clean and well lit. 1. Cluttered benches and dark areas invite accidents. Keep bystanders, children, and visitors away. 2. Distractions can cause you to lose control. Keep children out of the work area. Stay alert. Watch what you are doing and use common sense during assembly 3. and use of this product. During assembly dress properly. Do not wear loose clothing or jewelry. Con4. tain long hair. Do not overreach. Keep proper footing and balance at all times. 5. Use safety equipment during assembly. Always wear eye protection. 6. Always wear ANSI-approved safety goggles when assembling and using the Planishing Hammer Stand. REV 07j Do not force the product. Use the correct product for your application. 7. The correct product will do the job better and safer at the rate for which it is designed. Do not force the product and do not use it for a purpose for which it is not intended. Store an idle Planishing Hammer Stand out of reach of children and other 8. untrained persons. Maintain this product with care. 9. Use only accessories that are recommended by the manufacturer for your 10. model. Accessories that may be suitable for one product may become hazardous when used on another product. Maintain labels and nameplates on the Planishing Hammer Stand. 11. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Maintain a safe working environment. 12. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. Do not use to support any items other than SKU 94847, Planishing Hammer.13. Use on a flat, level surface capable of supporting the Planishing Hammer 14. Stand, the Planishing Hammer, the metal being worked on, and the vibration of the planishing process. Do not use this Planishing Hammer Stand as a stepping stool or ladder. 15. Never sit, stand, or climb on this Planishing Hammer Stand. Never allow children to play on or climb on this Stand. Only fill the Planishing Hammer Stand with sand. 16. Assembly Instructions Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 7. Connect Main Support (3) to Table Support (2). Insert two Bolts (6) with Washers 1. (10) down through the Table Support (2) and Main Support (3). Slide on two more Washers (10), Spring Washers (9) and thread on the Nuts (7). Leg (1) Table Support (2) Bolts (4), Washers (10) Spring Washers (9) andNuts (7) (not visible) Figure 1 2. Attach Table Support (2) to Leg (1). Insert two Bolts (4) with Washers (10) down through the Table Support (2) and down through the Leg (1). Slide on two more Washers (10), Spring Washers (9) and thread on the Nuts (7) - see Figure 1. Secure Cross Bar (8) to both the Main Support (3) and Leg (1). Slide Spring Washer 3. (9) and Washer (10) onto Bolt (5). Thread in through Main Support (3) and into Cross Bar (8). From the opposite side, slide Spring Washer (9) and Washer (10) onto second Bolt (5) and thread into Leg (1) and into Cross Bar (8). Tighten all hardware. 4. Check the Planishing Hammer Stand to make certain that it sits evenly, fully resting 5. on the ground. Make certain that all hardware is fully tightened. Plug (11) Main Support (3) Figure 2 6. Unscrew and remove both Plugs (11)-see Figure 2-and fill the Stand with sand to reduce noise when using the Planishing Hammer. Only use sand to fill the Stand. Do not use any other material or any liquid to fill the Stand. Screw the Plugs back onto the Stand. Place the Planishing Hammer on top of the Stand and align the mounting holes of 7. both Stand and Planishing Hammer. Position the operating portion of the planishing hammer above the Leg (1) of the stand as shown on the cover picture. REV 07f Secure Planishing Hammer to the Planishing Hammer Stand by sliding a grade-5 8. bolt (not included) of adequate length through a flat washer (not included), then through the base hole of the Planishing Hammer, and then through the mounting plate of the Stand. Slide another flat washer (not included) over the bolt. Attach a self-locking nut (not included). Repeat this operation for the remaining mounting holes. Then tighten all the nuts. The Planishing Hammer Stand has three 7/16” holes for mounting the Stand to your 9. work surface (hardware not included). Use on a flat, level surface capable of supporting the Planishing Hammer Stand, the Planishing Hammer, the metal being worked on, and the vibration of the planishing process. INSPECTION, MAINTENANCE, AND CLEANING Clean the Planishing Hammer Stand with a damp cloth. Do not use abrasives, 1. harsh chemicals or detergents as these will scratch and damage the Planishing...