Votes - 3, Average rating: 4
(
)
)
|
manual abstract
3. Charge the battery cartridge withtemperature at 10. C - 40. C (50. F - 104. F).( room ) Let a hot battery cartridge cool down before charging it. FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 1. Red part 2. Button 3. Battery cartridge 007451 • Always switch off the tool before installation or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. 1 2 3 4 Switch action Reversing switch action 1. Switch trigger 1. Reversing switch lever 1 A B 1 008664 CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Electric brake This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after switch trigger release, have tool serviced at a Makita service center. Lighting up the front lamp 1. Lamp 1 008668 CAUTION: • Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The light automatically goes out 10 - 15 seconds after the switch trigger is released. NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. 008665 This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Selecting correct socket Always use the correct size socket for bolts and nuts. An incorrect size socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut. Installing or removing socket 1 2 1. Socket 2. Anvil 008667 To install the socket, push it onto the anvil of the tool until it locks into place. To remove the socket, simply pull it off. 5 0 1.0 2.0 3.0 4.0 5.0 (S) M8(5/16") M10(3/8") M10(3/8") M8(5/16") Fastening time Fastening torqueProper fastening torque80 100 60 120 140 (101) (87) (72) (58) (43) 40 (29) 20 (14) M12(1/2") High tensile bolt N m (ft.lbs) . M12(1/2") 0 1.0 2.0 3.0 4.0 5.0 (S) M8(5/16") M10(3/8") M10(3/8") M8(5/16") Fastening time Fastening torqueProper fastening torque80 100 60 120 140 (101) (87) (72) (58) (43) 40 (29) 20 (14) M12(1/2") High tensile bolt N m (ft.lbs) . M12(1/2") CAUTION: • Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Hold the tool firmly and place the socket over the bolt or nut. Turn the tool on and fasten for the proper fastening time. The proper fastening torque may differ depending upon the kind or size of the bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. Standard bolt N m. 140 (ft.lbs) (101) 120 (87) 100 008670 NOTE: • Hold the tool pointed straight at the bolt or nut. • Excessive fastening torque may damage the bolt/nut or socket. Before starting your job, always perform a test operation to determine the proper fastening time for your bolt or nut. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery ...